View AM79C874_6572.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRELIMINARY
AM79C874
NetPHYTM-1LP Low Power 10/100-TX/FX Ethernet Transceiver
DISTINCTIVE CHARACTERISTICS
s 10/100BASE-TX Ethernet PHY device with 100BASE-FX fiber optic support s Typical power consumption of 0.3 W s Sends/receives data reliably over cable lengths greater than 130 meters s MII mode supports 100BASE-X and 10BASE-T s 7-Wire (General Purpose Serial Interface (GPSI)) mode supports 10BASE-T s Three PowerWiseTM management modes (from 300 mW typical) -- Power down: only management responds Typical power = 3 mW -- Unplugged: no cable, no receive clock Typical power = 100 mW -- Idle wire: no wire signal, no receiver power Typical power = 285 mW; MAC saves over 100 mW s Supports 1:1 or 1.25:1 transmit transformer -- Using a 1.25:1 ratio saves 20% transmit power consumption -- No external filters or chokes required s Waveshaping - no external filter required s Full and half-duplex operation with full-featured Auto-Negotiation function s LED indicators: Link, TX activity, RX activity, Collision, 10 Mbps, 100 Mbps, Full or Half Duplex s MDIO/MDC operates up to 25 MHz s Automatic Polarity Detection s Built-in loopback and test modes s Single 3.3-V power supply with 5-V I/O tolerance s 12 mm x 12 mm 80-pin TQFP package s Support for industrial temperature (-40C to +85C)
GENERAL DESCRIPTION
The AM79C874 NetPHY-1LP device provides the physical (PHY) layer and transceiver functions for one 10/100 Mbps Ethernet port. It delivers the dual benefits of CMOS low power consumption and small package size. Operating at 3.3 V, it consumes only 0.3 W. Three power management modes provide options for even lower power consumption levels. The small 12x12 mm 80-pin PQL package conserves valuable board space on adapter cards, switch uplinks, and embedded Ethernet applications. The NetPHY-1LP 10/100 Mbps Ethernet PHY device is IEEE 802.3 compliant. It can receive and transmit data reliably at over 130 meters. It includes on-chip input filtering and output waveshaping for unshielded twisted pair operation without requiring external filters or chokes. The NetPHY-1LP device can use 1:1 isolation transformers or 1.25:1 isolation transformers. 1.25:1 isolation transformers provide 20% lower transmit power consumption. A PECL interface is available for 100BASE-FX applications. Interface to the Media Access Controller (MAC) layer is established via the standard Media Independent Interface (MII), a 5-bit symbol interface, or a 7-wire (GPSI) interface. Auto-Negotiation determines the network speed and full or half-duplex operation. Automatic polarity correction is performed during Auto-Negotiation and during 10BASE-T signal reception. Multiple LED pins are provided for front panel status feedback. One option is to use two bi-color LEDs to show when the device is in 100BASE-TX or 10BASE-T mode (by illuminating), Half or Full Duplex (by the color), and when data is being received (by blinking). Individual LEDs can indicate link detection, collision detection, and data being transmitted. The NetPHY-1LP device needs only one external 25MHz oscillator or crystal because it uses a dual-speed clock synthesizer to generate all other required clock domains. The receiver has an adaptive equalizer/DC restoration circuit for accurate clock/data recovery from the 100BASE-TX signal. The NetPHY-1LP device is available in the commercial (0C to +70C) or industrial (-40C to +85C) temperature ranges. The industrial temperature range is well suited to environments, such as enclosures with restricted air flow or outdoor equipment.
Refer to AMD's Website (www.amd.com) for the latest information.
Publication# 22235 Rev: I Amendment/0 Issue Date: April 2001
PRELIMINARY
BLOCK DIAGRAM
PCS Framer Carrier Detect 4B/5B MII Data Interface Interface MAC MDC/MDIO
PMA Clock Recovery Link Monitor Signal Detect
TP_PMD MLT-3 BLW Stream Cipher 25 MHz 10TX
100TX TX+ 100RX Mux TX-
10BASE-T
10RX
RX+ RX-
Transformer
Control/Status
20 MHz RX FLP
MII Serial Management Interface and Registers
PLL Clk Generator Test LED Control
25 MHz
AutoNegotiation
PHYAD[4:0]
XTL+ XTL-
CLK
TEST LED Drivers
22235I-1
2
AM79C874
PRELIMINARY
CONNECTION DIAGRAM
TVCC2 TVCC1 TXTX+ TGND2 XTL+ XTLREFVCC IBREF REFGND FXTFXT+ TEST2 TEST1/FXR+ TEST0/FXREQGND RX+ RXTEST3/SDI+ RPTR 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 PCSBP ISODEF ISO TGND1 REFCLK CLK25 BURN_IN RST PWRDN PLLVCC PLLGND OGND1 OVDD1 PHYAD[4]/10RXDPHYAD[3]/10RXD+ PHYAD[2]/10TXD++ PHYAD[1]/10TXD+ PHYAD[0]/10TXDGPIO[0]/10TXD--/7Wire GPIO[1]/TP125 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 EQVCC ADPVCC LEDDPX/LEDTXB LEDSPD[1]/LEDTXA/CLK25EN ANEGA TECH_SEL[0] TECH_SEL[1] TECH_SEL[2] CRVVCC CRVGND OGND2 OVDD2 LEDLNK/LED_10LNK/LED_PCSBP_SD LEDTX/LEDBTB LEDRX/LEDSEL LEDCOL/SCRAM_EN LEDSPD[0]/LEDBTA/FX_SEL INTR CRS/10CRS COL/10COL AM79C874
NetPHY-1LP
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
MDIO MDC RXD[3] RXD[2] RXD[1] RXD[0]/10RXD VDD1 DGND1 RX_DV RX_CLK/10RXCLK RX_ER/RXD[4] TX_ER/TXD[4] TX_CLK/10TXCLK/PCSBP_CLK TX_EN/10TXEN DGND2 VDD2 TXD[0]/10TXD TXD[1] TXD[2] TXD[3]
22235I-2
AM79C874
3
PRELIMINARY
ORDERING INFORMATION Standard Products
AMD standard products are available in several packages and operating ranges. The order number (Valid Combination) is formed by a combination of the elements below. AM79C874 V C/I
ALTERNATE PACKAGING OPTION Not Applicable
TEMPERATURE RANGE C = Commercial (0C to +70C) I = Industrial (-40C to +85C) PACKAGE TYPE V = 80-Pin Thin Plastic Quad Flat Pack (PQT 80) SPEED OPTION Not Applicable
DEVICE NUMBER/DESCRIPTION AM79C874 NetPHY-1LP Low Power 10/100-TX/FX Ethernet Transceiver
Valid Combinations AM79C874 AM79C874 VC VI
Valid Combinations Valid Combinations list configurations planned to be supported in volume for this device. Consult the local AMD sales office to confirm availability of specific valid combinations and to check on newly released combinations.
4
AM79C874
PRELIMINARY
RELATED AMD PRODUCTS
Part No. Controllers Am79C90
Description
CMOS Local Area Network Controller for Ethernet (C-LANCETM)
Integrated Controllers Am79C940 Am79C961A Am79C965A Am79C970A Am79C973/ Am79C975 Am79C976 Am79C978 Media Access Controller for Ethernet (MACETM) PCnetTM-ISA II Full Duplex Single-Chip Ethernet Controller for ISA Bus PCnetTM-32 Single-Chip 32-Bit Ethernet Controller for 486 and VL Buses PCnetTM-PCI II Full Duplex Single-Chip Ethernet Controller for PCI Local Bus PCnetTM-FAST III Single-Chip 10/100 Mbps PCI Ethernet Controller with Integrated PHY PCnetTM-PRO 10/100 Mbps PCI Ethernet PCI Controller PCnetTM-Home Single-Chip 1/10 Mbps PCI Home Networking Controller
Physical Layer Devices (Single-Port) Am79C901 HomePHYTM Single-Chip 1/10 Mbps Home Networking PHY
Physical Layer Devices (Multi-Port) Am79C875 NetPHYTM-4LP Low Power Quad10/100-TX/FX Ethernet Transceiver
Integrated Repeater/Hub Devices Am79C984A Am79C985 Enhanced Integrated Multiport Repeater (eIMRTM) Enhanced Integrated Multiport Repeater Plus (eIMR+TM)
AM79C874
5
PRELIMINARY
TABLE OF CONTENTS
DISTINCTIVE CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 CONNECTION DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ORDERING INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Standard Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 RELATED AMD PRODUCTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 PIN DESIGNATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 PIN DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Media Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 MII/7-Wire (GPSI) Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Miscellaneous Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 LED Port Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Bias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Power and Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 FUNCTIONAL DESCRIPTION15 Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 MII Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 7-Wire (GPSI) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 5B Symbol Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 100BASE-X Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Transmit Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Receive Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 4B/5B Encoder/Decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Scrambler/Descrambler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Link Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 MLT-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Adaptive Equalizer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Baseline Wander Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Clock/Data Recovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 PLL Clock Synthesizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 10BASE-T Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Twisted Pair Transmit Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Twisted Pair Receive Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Twisted Pair Interface Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Collision Detect Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Jabber Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Reverse Polarity Detection and Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Auto-Negotiation and Miscellaneous Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Auto-Negotiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Parallel Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Far-End Fault. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 SQE (Heartbeat) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Loopback Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 LED Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Power Savings Mechanisms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Selectable Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Power Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Unplugged . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Idle Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 PHY CONTROL AND MANAGEMENT BLOCK (PCM BLOCK) . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Register Administration for 100BASE-X PHY Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Description of the Methodology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Bad Management Frame Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
6
AM79C874
PRELIMINARY REGISTER DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Serial Management Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 MII Management Control Register (Register 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 MII Management Status Register (Register 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 PHY Identifier 1 Register (Register 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 PHY Identifier 2 Register (Register 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Auto-Negotiation Advertisement Register (Register 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Auto-Negotiation Link Partner Ability Register in Base Page Format (Register 5) . . . . . . . . 33 Auto-Negotiation Link Partner Ability Register in Next Page Format (Register 5) . . . . . . . . .33 Auto-Negotiation Expansion Register (Register 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Auto-Negotiation Next Page Advertisement Register (Register 7) . . . . . . . . . . . . . . . . . . . . 35 Reserved Registers (Registers 8-15, 20, 22, 25-31) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Miscellaneous Features Register (Register 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Interrupt Control/Status Register (Register 17) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Diagnostic Register (Register 18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Power/Loopback Register (Register 19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Mode Control Register (Register 21). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Disconnect Counter Register (Register 23). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Receive Error Counter Register (Register 24). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 OPERATING RANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Commercial (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Industrial (I) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 DC CHARACTERISTICS41 SWITCHING WAVEFORMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Key to Switching Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 SWITCHING CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 System Clock Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 MLT-3 Signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 MII Management Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 MII Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 100 Mbps MII Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 100 Mbps MII Receive Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 10 Mbps MII Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 10 Mbps MII Receive Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 GPSI Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 10 Mbps GPSI Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 10 Mbps GPSI Receive Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 10 Mbps GPSI Collision Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 10 Mbps GPSI Transmit Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 10 Mbps GPSI Transmit Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 PHYSICAL DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 PQT80 (measured in millimeters) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 REVISION HISTORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
List of Figures
Figure 1.FXT and FXR Termination for 100BASE-FX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 2.MLT-3 Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 3.TX and RX Termination for 100BASE-TX and 10BASE-T. . . . . . . . . . . . . . . . . . . . . 21 Figure 5.Standard LED Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure 6.Advanced LED Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 7.PHY Management Read and Write Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Figure 8.MLT-3 Receive Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Figure 9.MLT-3 and 10BASE-T Test Load with 1:1 Transformer Ratio. . . . . . . . . . . . . . . . . . . . . 44 Figure 10.MLT-3 and 10BASE-T Test Load with 1.25:1 Transformer Ratio . . . . . . . . . . . . . . . . . 44 Figure 11.Near-End 100BASE-TX Waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Figure 12.10BASE-T Waveform With 1:1 Transformer Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
AM79C874
7
PRELIMINARY Figure 13.PECL Test Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 14.Clock Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 15.MLT-3 Test Waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 16.Management Bus Transmit Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 17.Management Bus Receive Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 18.100 Mbps MII Transmit Start of Packet Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 19.100 Mbps Transmit End of Packet Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 20.100 Mbps MII Receive Start of Packet Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 21.100 Mbps MII Receive End of Packet Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 22.10 Mbps MII Transmit Start of Packet Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 23.10 Mbps MII Transmit End of Packet Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 24.10 Mbps MII Receive Start of Packet Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 25.10 Mbps MII Receive End of Packet Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 26.GPSI Receive Timing - Start of Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 27.GPSI Receive Timing - End of Reception (Last Bit = 0) . . . . . . . . . . . . . . . . . . . . . . . Figure 28.GPSI Receive Timing - End of Reception (Last Bit = 1) . . . . . . . . . . . . . . . . . . . . . . . Figure 29.GPSI Collision Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 30.GPSI Transmit Timing - Start of Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 31.GPSI Transmit 10TXCLK and 10TXD Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Figure 32.Test Load for 10RXD, 10CRS, 10RXCLK, 10TXCLK and 10COL . . . . . . . . . . . . . . . . 45 46 46 47 47 48 49 50 51 52 53 54 55 56 56 57 57 58 58 58
List of Tables
Table 1.MII Pins That Relate to 10 Mbps 7-Wire (GPSI) Mode . . . . . . . . . . . . . . . . . . . . . . . . . .16 Table 2.Code-Group Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Table 3.Speed and Duplex Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Table 4.Standard LED Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Table 5.Advanced LED Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Table 6.Clause 22 Management Frame Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Table 7.PHY Address Setting Frame Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 Table 8.Register Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Table 9.Legend for Register Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Table 10.MII Management Control Register (Register 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Table 11.MII Management Status Register (Register 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Table 12.PHY Identifier 1 Register (Register 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Table 13.PHY Identifier 2 Register (Register 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Table 14.Auto-Negotiation Advertisement Register (Register 4) . . . . . . . . . . . . . . . . . . . . . . . . .32 Table 15.Auto-Negotiation Link Partner Ability Register in Base Page Format (Register 5) . . . .33 Table 16.Auto-Negotiation LInk Partner Ability Register in Next Page Format (Register 5) . . . . .33 Table 17.Auto-Negotiation Expansion Register (Register 6) . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Table 18.Auto-Negotiation Next Page Advertisement Register (Register 7) . . . . . . . . . . . . . . . .35 Table 19.Miscellaneous Features Register (Register 16) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Table 20.Interrupt Control/Status Register (Register 17) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Table 21.Diagnostic Register (Register 18) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Table 22.Power/Loopback Register (Register 19) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Table 23.Mode Control Register (Register 21) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Table 24.Disconnect Counter (Register 23) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Table 25.Receive Error Counter Register (Register 24) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
8
AM79C874
PRELIMINARY
PIN DESIGNATIONS
Listed by Pin Number
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Pin Name PCSBP ISODEF ISO TGND1 REFCLK CLK25 BURN_IN RST PWRDN PLLVCC PLLGND OGND1 OVDD1 PHYAD[4]/10RXDPHYAD[3]/10RXD+ PHYAD[2]/10TXD++ PHYAD[1]/10TXD+ PHYAD[0]/10TXDGPIO[0]/10TXD--/ 7Wire GPIO[1]/TP125
Pin No. 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
Pin Name MDIO MDC RXD[3] RXD[2] RXD[1] RXD[0]/10RXD VDD1 DGND1 RX_DV RX_CLK/10RXCLK RX_ER/RXD[4] TX_ER/TXD[4] TX_CLK/10TXCLK/ PCSBP_CLK TX_EN/10TXEN DGND2 VDD2 TXD[0]/10TXD TXD[1] TXD[2] TXD[3]
Pin No. 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60
Pin Name COL/10COL CRS/10CRS INTR LEDSPD[0]/ LEDBTA/FX_SEL LEDCOL/ SCRAM_EN LEDRX/LEDSEL LEDTX/LEDBTB LEDLNK/ LED_10LNK/ LED_PCSBP_SD OVDD2 OGND2 CRVGND CRVVCC TECH_SEL[2] TECH_SEL[1] TECH_SEL[0] ANEGA LEDSPD[1]/ LEDTXA/CLK25EN LEDDPX/LEDTXB ADPVCC EQVCC
Pin No. Pin Name 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 RPTR TEST3/SDI+ RXRX+ EQGND TEST0/FXRTEST1/FXR+ TEST2 FXT+ FXTREFGND IBREF REFVCC XTLXTL+ TGND2 TX+ TXTVCC1 TVCC2
AM79C874
9
PRELIMINARY
PIN DESCRIPTIONS
The following table describes terms used in the pin descriptions.
Term Input Analog Input Output Analog Output High Impedance Pull-Up Pull-Down Description Digital input to the PHY Analog input to the PHY Digital output from the PHY Analog output from the PHY Tri-state capable output from the PHY PHY has internal pull-up resistor. NC=HIGH PHY has internal pull-down resistor. NC=LOW
TEST3/SDI+ FX Transceiver Signal Detect Analog Output/Input When BURN_IN (Pin 7) is pulled high, this pin serves as a test mode output monitor pin. This pin is not connected in 10/100BASE-TX mode. When FX_SEL (Pin 44) is pulled low, this pin becomes the Signal Detect input from the Fiber-Optic transceiver. When the signal quality is good, the SDI+ pin should be driven high.
MII/7-Wire (GPSI) Signals
RXD[3:0] MII Receive Data Output, High Impedance
The data is synchronous with RX_CLK when RX_DV is active. When the 7-wire 10BASE-T interface operation is enabled (GPIO[0]= HIGH), RXD[0] will serve as the 10 MHz serial data output. RX_DV Receive Data Valid Output, High Impedance
Media Connections
TX Transmitter Outputs Analog Output
The TX pins are the differential transmit output pair. The TX pins transmit 10BASE-T or MLT-3 signals depending on the state of the link of the port. RX Receiver Input Analog Input
The RX pins are the differential receive input pair. The RX pins can receive 10BASE-T or MLT-3 signals depending on the state of the link of the port. FXT FX Transmit Analog Output
RX_DV is asserted when the NetPHY-1LP device is presenting recovered nibbles on RXD[3:0]. This includes the preamble through the last nibble of the data stream on RXD[3:0]. In 100BASE-X mode, the /J/K/ is considered part of the preamble; thus RX_DV is asserted when /J/K/ is detected. In 10BASE-T mode, RX_DV is asser ted (and data is presented on RXD[3:0]) when the device detects valid preamble bits. RX_DV is synchronized to RX_CLK. RX_CLK/10RXCLK Receive Clock Output, High Impedance
These pins are not connected in 10/100BASE-TX mode. When FX_SEL (Pin 44) is pulled low, these pins become the ECL level transmit output for 100BASE-FX. TEST0/FXRTest Output/FX Receive -Analog Output/Input
When BURN_IN (Pin 7) is pulled high, this pin serves as a test mode output monitor pin. When FX_SEL (Pin 44) is pulled low, this pin becomes an ECL level negative receive input for 100BASE-FX. This pin can be left unconnected when the device is operating in 100BASE-TX or 10BASE-T mode. TEST1/FXR+ Test Output/FX Receive +Analog Output/Input
A continuous clock (which is active while LINK is established) provides the timing reference for RX_DV, RX_ER, and RXD[3:0] signals. It is 25 MHz in 100BASE-TX/FX and 2.5 MHz in 10BASE-T. To further reduce power consumption of the overall system, the device provides an optional mode enabled through MII Register 16, bit 0 in which RX_CLK is held inactive (low) when no data is received. If RX_CLK is needed when LINK is not established, the NetPHY-1LP must be placed into digital loopback or force the link via register 21, bits 13 or 14. When 7-wire 10BASE-T mode is enabled, this pin will provide a 10 MHz clock. RX_CLK is high impedance when the ISO pin is enabled RX_ER/RXD[4] Receive Error Output, High Impedance
When BURN_IN (Pin 7) is pulled high, this pin serves as a test mode output monitor pin. When FX_SEL (Pin 44) is pulled low, this pin becomes an ECL level positive receive input for 100BASE-FX. This pin can be left unconnected when the device is operating in 100BASE-TX or 10BASE-T mode.
When RX_ER is active high, it indicates an error has been detected during frame reception. This pin becomes the highest-order bit of the receive 5bit code group in PCS bypass (PCSBP=HIGH) mode. This output is ignored in 10BASE-T operation.
10
AM79C874
PRELIMINARY TX_ER/TXD[4] Transmit Error CRS/10CRS Carrier Sense
Input
Output, High Impedance
When TX_ER is asserted, it will cause the 4B/5B encoding process to substitute the transmit error codegroup /H/ for the encoded data word. This pin becomes the higher-order bit of the transmit 5bit code group in PCS bypass (PCSBP=HIGH) mode. This input is ignored in the 10BASE-T operation. TX_CLK/10TXCLK/PCSBPCLK Transmit Clock Output, High Impedance A free-running clock which provides timing reference for TX_EN, TX_ER, and TXD[3:0] signals. It is 25 MHz in 100BASE-TX/FX and 2.5 MHz in 10BASE-T. When 7-wire GPSI mode is enabled, this pin will provide a 10 MHz transmit clock for 10BASE-T operation. When the cable is unplugged, the 10TXCLK ceases operation. When working in PCSBP mode, this pin will provide a 25 MHz clock for 100BASE-TX operation, and 20 MHZ clock for 10BASE-T operation. TX_CLK is high impedance when the ISO pin is enabled. TX_EN/10TXEN Transmit Enable Input
CRS is asserted high when twisted pair media is nonidle. This signal is used for both 10BASE-T and 100BASE-X. In full duplex mode, CRS responds only to RX activity. In half duplex mode, CRS responds to both RX and TX activity. 10CRS is used as the carrier sense output for the 7-wire interface mode.
Miscellaneous Functions
PCSBP PCS Bypass Input, Pull-Down
The 100BASE-TX PCS as well as scrambler/descrambler will be bypassed when PCSBP is pulled high via a 10 kW resistor. TX_ER will become TXD[4] and RX_ER will become RXD[4]. In 10 Mbps PCS bypass mode, the MII signals are not valid. The signals that interface to the MAC (i.e., DECPC 21143) are located on pins 14 to 19. The signals are defined as follows: -- 10RXD are the differential receive outputs to the MAC. -- 10TXD are the differential transmit inputs from the MAC. -- 10TXD++/10TXD-- are the differential preemphasis transmit outputs from the MAC. When left unconnected, the device operates in MII or GPSI mode. ISODEF Isolate Default Input, Pull-Down
The TX_EN pin is asserted by the MAC to indicate that data is present on TXD[3:0]. When 7-wire 10BASE-T mode is enabled, this pin is the transmit enable signal. TXD[3:1] Transmit Data Input
The MAC will source TXD[3:1] to the PHY. The data will be synchronous with TX_CLK when TX_EN is asserted. The PHY will clock in the data based on the rising edge of TX_CLK. TXD[0]/10TXD Transmit Data[0]/10 Mbps Transmit Data Input
This pin is used when multiple PHYs are connected to a single MAC. When it is pulled high via a 10 kW resistor, the MII interface will be high impedance. The status of this pin will be latched into MII Register 0, bit 10 after reset. When this pin is left unconnected, the default condition of the MII output pins are not in the high impedance state. ISO Isolate Input, Pull-Down
The MAC will source TXD[0] to the PHY. The data will be synchronous with TX_CLK when TX_EN is asserted. The PHY will clock in the data based on the rising edge TX_CLK. When 7-wire 10BASE-T mode is enabled, this pin will transmit serial data. COL/10COL Collision Output, High Impedance
COL is asserted high when a collision is detected on the media. COL is also used for the SQE test function in 10BASE-T mode. 10COL is asserted high when a collision is detected during 7-wire interface mode.
The MII output pins will become high impedance when ISO is pulled high via a 10 kW resistor. However, the MII input pins will still respond to data. This allows multiple PHYs to be attached to the same MII interface. The same isolate condition can also be achieved by asserting MII Register 0, bit 10. In repeater mode, ISO will not tri-state the CRS pin. When this pin is left unconnected, the MII output pins are not in the high impedance state.
AM79C874
11
PRELIMINARY REFCLK Clock Input tions). Each pin should either be pulled low via a 1 kW - 4.7 kW resistor (set bit to zero) or left unconnected (set bit to 1) in order to achieve the desired PHY address. New address changes take effect after a reset has been issued, or at power up. In PCS bypass mode, PHYAD[4:0] and GPIO[1:0] serves as 10BASE-T serial input and output. Note: In GPSI mode, the PHYAD pins must be set to addresses other than 00h. GPIO[0]/10TXD--/7Wire General Purpose I/O 0 Input/Output, Pull-Up
Input, Pull-Down
This pin connects to a 25-MHz +50 ppm clock source with a 40% to 60% duty cycle. When a crystal input is used, this pin should be pulled low via a 1 kW resistor. XTL Crystal Inputs Analog Input
These pins should be connected to a 25-MHz crystal. The crystal should be parallel resonant and have a frequency stability of +100 ppm and a frequency tolerance of +50 ppm. REFCLK (Pin 5) should be pulled low when the crystal is used as a clock source. These pins may be left unconnected when REFCLK is used as a clock source. CLK25 25 MHz Clock Output
If this pin is pulled low via a 10 kW resistor, on the rising edge of reset, the device will operate in 10BASE-T 7-wire (GPSI) mode. If this pin is left unconnected during the rising edge of reset, the device will operate in standard MII mode. After the reset operation has completed, this pin can function as an input or an output (dependent on the value of GPIO[0] DIR (MII Register 16, bit 6). If MII Register 16, bit 6 is set HIGH, GPIO[0] is an input. The input value on the GPIO[0] pin will be reflected in MII Register 16, bit 7 - GPIO[0] Data. If MII Register 16, bit 6 is set LOW, GPIO[0] is an output. The value of MII Register 16, bit 7 will be reflected on the GPIO[0] output pin. GPIO[1]/TP125 General Purpose I/O 1 Input/Output, Pull-Down
When the CLK25EN pin is pulled low, the CLK25 pin provides a continuous 25 MHz clock to the MAC. BURN_IN Test Enable Input, Pull-Down
When pulled high via a 10 kW resistor, this pin forces the NetPHY-1LP device into Burn-in mode for reliability assurance control. When left unconnected the device operates normally. TEST2 Test Output Analog Output
When BURN_IN (pin 7) is pulled high, this pin serves as a test mode output monitor pin. TEST2 can be left unconnected when the device is operating. RST Reset Input, Pull-Up
A LOW input forces the NetPHY-1LP device to a known reset state. The chip can also be reset through internal power-on-reset or MII Register 0, bit 15. PWRDN Power Down Input, Pull-Down
If this pin is pulled high via a 10 kW resistor, on the rising edge of reset, the device will be enabled for use with a 1.25:1 transmit ratio transformer. If this pin is left unconnected during the rising edge of reset, the device will be enabled for use with a 1:1 transmit ratio transformer. After the reset operation has completed, this pin can function as an input or an output (dependent on the value of GPIO[1] DIR - MII Register 16, bit 8). If MII Register 16, bit 8 is set HIGH, GPIO[1] is an input. The input value on the GPIO[1] pin will be reflected in MII Register 16, bit 9 - GPIO[1] Data. If MII Register 16, bit 8 is set LOW, GPIO[1] is an output. The value of MII Register 16, bit 9 will be reflected on the GPIO[1] output pin. MDIO Management Data Input/Output Pull-Down
If this pin is pulled high via a 10 kW resistor on the rising edge of reset, the device will power down the analog modules and reset the digital circuits. However, the device will still respond to MDC/MDIO data. The same power-down state can also be achieved through the MII Register 0, bit 11. However, the device will respond activity on the PWRDN pin even when bit 11 is not set. When left unconnected, the device operates normally. PHYAD[4:0] PHY Address Input/Output, Pull-Up
These pins allow 32 configurable PHY addresses. The PHYAD will also determine the scramble seed, which helps to reduce EMI when there are multiple ports switching at the same time (repeater/switch applica-
This pin is a bidirectional data interface used by the MAC to access management registers within the NetPHY-1LP device. This pin has an internal pull-down, therefore, it requires a 1.5 kW pull-up resistor as specified in IEEE 802.3 when interfaced with a MAC. This pin can be left unconnected when management is not used.
12
AM79C874
PRELIMINARY MDC Management Data Clock RPTR Repeater Mode
Input
Input
This clock is sourced by the MAC and is used to synchronize MDIO data. When management is not used, this pin should be tied to ground. INTR Interrupt Output, High Impedance
This pin should be tied to ground via a 10 kW resistor if repeater mode is to be disabled. When this pin is pulled high via a 10 kW resistor, repeater mode will be enabled. Repeater mode can also enabled via MII Register 16, bit 15.
This pin is used to signal an interrupt to the MAC. The pin will be forced high or low (normally high impedance) to signal an interrupt depending upon the value of the INTR_LEVL bit, MII Register 16, bit 14. The events which trigger an interrupt can be programmed via the Interrupt Control Register (Register 17). TECH_SEL[2:0] Technology Select Input, Pull-Up
LED Port Pins
LEDRX/LED_SEL Receive LED/LED Configuration Select Input/Output, Pull-Up When this pin is pulled low via a 5 kW resistor, on the rising edge of reset, the advanced LED configuration is enabled. If there is no pull-down resistor present, on the rising edge of reset, the standard LED configuration is enabled. After the rising edge of reset this pin controls the Receive LED. This pin toggles between high and low when data is received. When the device is operating in the standard LED mode, refer to Table 4 and Figure 5 in the LED Port Configuration section. When the device is operating in the advanced LED mode, refer to Table 5 and Figure 6 in the LED Port Configuration section. LEDCOL/SCRAM_EN Collision LED/Scrambler Enable Input/Output, Pull-Up When this pin is pulled low via a 1-kW resistor, on the rising edge of reset, the scrambler/descrambler is disabled. If no pull-down resistor is present, on the rising edge of reset, the scrambler/descrambler is enabled. After the rising edge of reset this pin controls the Collision LED. This pin toggles between high and low when there is a collision in half-duplex operation. In fullduplex operation this pin is inactive. When the device is operating in the standard LED mode (see LEDRX/LEDSEL pin description), refer to Table 4 and Figure 5 in the LED Port Configuration section. When the device is operating in the advanced LED mode (see LEDRX/LEDSEL pin description), see Table 5 and Figure 6. LEDLNK/LED_10LNK/LED_PCSBP_SD Link LED/7-Wire Link LED/PCSBP Signal Detect Output W h en a l i n k i s e s t abl i s h ed i n 1 0 0B A S E - X or 10BASE-T mode, this pin will assume a logic low level. When a link is established in 7-Wire mode, this pin will assume a logic high level. When in PCS Bypass mode, this pin assumes a logic high level indicating Signal Detect. Refer to Table 4 and Figure 4 in the LED Port Configuration section if the device is operating in the standard LED mode. See Table 5 and Figure 5 if the device is operating in the advanced LED mode.
The Technology Select pins, in conjunction with the ANEGA pin, set the speed and duplex configurations for the device on the rising edge of reset. These capabilities are reflected in MII Register 1 and MII Register 4. Table 3 lists the possible configurations for the device. If the input is listed as LOW, the pin should be pulled to ground via a 10 kW resistor on the rising edge of reset. If the input is listed as HIGH, the pin can be left unconnected. Note: By using resistors to hard wire the TECH_SEL[2:0] pins and the ANEGA pin, using the MDC/MDIO management interface pins becomes optional. The device's speed, duplex, and auto-negotiati o n c a p a b i l i ti e s a r e s e t v i a h ar dwa r e. I f t h e management interface is used, the registers cannot be set to a higher capability than the hard-wired setting. The highest capabilities are Full Duplex, 100 Mbps, and Auto-Negotiation enabled. ANEGA Auto-Negotiation Ability Input, Pull-Up
When this pin is pulled to ground via a 10 kW resistor, on the rising edge of reset, Auto-Negotiation is disabled. When this pin is left unconnected, on the rising edge of reset, Auto-Negotiation is enabled. Note that this pin acts in conjunction with Tech_Sel[2:0] on the rising edge of reset. Refer to Table 3 to determine the desired configuration for the device. Note: By using resistors to hard wire the TECH_SEL[2:0] pins and the ANEGA pin, using the MDC/MDIO management interface pins becomes optional. The device's speed, duplex, and auto-negotiati o n c a p a b i l i ti e s a r e s e t v i a h ar dwa r e. I f t h e management interface is used, the registers cannot be set to a higher capability than the hard-wired setting. The highest capabilities are Full Duplex, 100 Mbps, and Auto-Negotiation enabled.
AM79C874
13
PRELIMINARY Note: If 7-Wire mode is chosen the polarity of the LED should be reversed and the cathode of the LED should be tied to ground. LEDSPD[0]/LEDBTA/FX_SEL 100 Mbps Speed LED/Advanced LED/Fiber Select Input/Output, Pull-Up When this pin is pulled low via a 1 kW resistor, on the rising edge of reset, the device will be enabled for 100BASE-FX operation. When no pull-down resistor is present, on the rising edge of reset, the device will be enabled for 100BASE-TX or 10BASE-T operation. When the standard LED configuration is enabled (see LEDRX/LEDSEL pin description), this pin serves as the 100 Mbps speed LED. A logic low level indicates 100 Mbps operation. A logic high level indicates 10 Mbps operation. Refer to Table 4 and Figure 5 in the LED Port Configuration section to determine the correct polarity of the LED. When the advanced LED configuration is enabled, this pin works in conjunction with LEDTX/LEDBTB (pin 47). Refer to Table 5 and Figure 6 in the LED Port Configuration section to determine the correct polarity of the bidirectional LED. LEDTX/LEDBTB Transmit LED/Advanced LED Output figuration section to determine the correct polarity of the bi-directional LED. LEDDPX/LEDTXB Duplex LED/Advanced LED Output
When the standard LED configuration is enabled (see LEDRX/LEDSEL description), this pin serves as the duplex LED. A logic low level indicates full duplex operation. A logic high level indicates half duplex operation. See Table 4 and Figure 5 in the LED Port Configuration section to determine the correct polarity of the LED. When the advanced LED configuration is enabled, this pin works in conjunction with LEDSPD[1] LEDTXA/ CLK25EN (pin 57). Refer to Table 5 and Figure 6 in the LED Port Configuration section to determine the correct polarity of the bi-directional LED.
Bias
IBREF Reference Bias Resistor Analog
This pin must be tied to an external 10.0 kW (1%) resistor which should be connected to ground. The 1% resistor provides the bandgap reference voltage.
Power and Ground
PLLVCC, OVDD1, OVDD2, VDD1, VDD2, CRVVCC, ADPVCC, EQVCC, REFVCC, TVCC1, TVCC2 Power Pins Power These pins are 3.3 V power for sections of the NetPHY-1LP device as follows: PLLVCC is power for the PLL; OVDD1 and OVDD2 are power for the I/O; VDD1 and VDD2 are power for the digital logic; CRVVCC is power for clock recovery; ADPVCC and EQVCC are power for the equalizer; REFVCC is power for the bandgap reference; and TVCC1 and TVCC2 are power for the transmit driver. PLLGND, OGND1, OGND2, DGND1, DGND2, CRVGND, EQGND, REFGND, TGND1, TGND2 Ground Pins Power These pins are ground for the power pins as follows: PLLGND is ground for PLLVCC; OGND is ground for OVDD; DGND is ground for VDD; CRVGND is ground for CRVVCC and ADPVCC; EQGND is ground for EQVCC; REFGND is ground for REFVCC; and TGND is ground for TVCC. Note: Bypass capacitors of 0.1 mF between the power and ground pins are recommended. The four areas where the capacitors must be very close to the pins (within 3 mm) are the PLL (pins 10 and 11), Clock Recovery (pins 51 and 52), Equalizer (pins 60 and 65), and Bandgap Reference (pins 71 and 73) areas. The other bypass capacitors should be placed as close to the pins as possible.
When the standard LED configuration is enabled (see LEDRX/LEDSEL pin description), this pin serves as the transmit LED. This pin toggles between high and low when data is transmitted. Refer to Table 4 and Figure 5 in the LED Port Configuration section to determine the correct polarity of the LED. When the advanced LED configuration is enabled, this pin works in conjunction with LEDSPD[0]/LEDBTA/ FX_SEL (pin 44). Refer to Table 5 and Figure 6 in the LED Port Configuration section to determine the correct polarity of the bi-directional LED. LEDSPD[1]/LEDTXA/CLK25EN 10 Mbps Speed LED/Advanced LED/25 MHz Clock Enable Input/Output, Pull-Up When this pin is pulled low via a 1 kW resistor, on the rising edge of reset, the device will output a 25 MHz clock on CLK25 (pin 6). When no pull-down resistor is present, on the rising edge of reset, CLK25 is inactive. When the standard LED configuration is enabled (see LEDRX/LEDSEL pin description), this pin serves as the 10 Mbps speed LED. A logic low level indicates 10 Mbps operation. A logic high level indicates 100 Mbps operation. Refer to Table 4 and Figure 5 in the LED Port Configuration section to determine the correct polarity of the LED. When the advanced LED configuration is enabled, this pin works in conjunction with LEDDPX/LEDTXB (pin 58). Refer to Table 5 and Figure 6 in the LED Port Con-
14
AM79C874
PRELIMINARY
FUNCTIONAL DESCRIPTION
The NetPHY-1LP device integrates the 100BASE-X PCS, PMA, and PMD functions and the 10BASE-T Manchester ENDEC and transceiver functions in a single chip for Ethernet 10 Mbps and 100 Mbps operations. It performs 4B/5B, MLT3, NRZI, and Manchester encoding and decoding, clock and data recovery, stream cipher scrambling/descrambling, adaptive equalization, line transmission, carrier sense and link integrity monitor, Auto-Negotiation, and MII management functions. It provides an IEEE 802.3u compatible Media Independent Interface (MII) to communicate with an Ethernet Media Access Controller (MAC). Selection of 10 Mbps or 100 Mbps operation is based on settings of internal Serial Management Interface registers or determined by the on-chip Auto-Negotiation logic. The device can be set to operate either in full-duplex mode or half-duplex mode for either 10 Mbps or 100 Mbps. The NetPHY-1LP device communicates with a repeater, switch, or MAC device through either the Media Independent Interface (MII) or the 10 Mbps 7-wire (GPSI) interface. The NetPHY-1LP device consists of the following functional blocks: s MII Mode s 7-Wire (GPSI) Mode s PCS Bypass (5B Symbol) Mode s 100BASE-X Block including: -- Transmit Process -- Receive Process -- 4B/5B Encoder and Decoder -- Scrambler and Descrambler -- Link Monitor -- MLT-3 -- Adaptive Equalizer -- Baseline Wander Compensation -- Clock/Data Recovery -- PLL Clock Synthesizer s 10BASE-T Block including: -- Transmit Process -- Receive Process -- Interface Status -- Collision Detect -- Jabber -- Reverse Polarity Detection and Correction s Auto-Negotiation and miscellaneous functions including:
-- Auto-Negotiation -- Parallel Detection -- Far-End Fault -- SQE (Heartbeat) -- Loopback Operation -- Reset s LED Port Configuration s Power Savings Mechanisms including: -- Selectable Transformer -- Power Down -- Unplugged -- Idle Wire s PHY Control and Management
Modes of Operation
The MII/GPSI/5B Symbol interface provides the data path connection between the NetPHY-1LP transceiver and the Media Access Controller (MAC), repeater, or switch. The MDC and MDIO pins are responsible for communication between the NetPHY-1LP transceiver and the station management entity (STA). The MDC and MDIO pins can be used in any mode of operation. MII Mode The purpose of the MII mode is to provide a simple, easy to implement connection between the MAC Reconciliation layer and the PHY. The MII is designed to make the differences between various media transparent to the MAC sublayer. The MII consists of a nibble wide receive data bus, a nibble wide transmit data bus, and control signals to facilitate data transfers between the PHY and the Reconciliation layer. s TXD (transmit data) is a nibble (4 bits) of data that are driven by the reconciliation sublayer synchronously with respect to TX_CLK. For each TX_CLK period which TX_EN is asserted, TXD[3:0] are accepted for transmission by the PHY. s TX_CLK (transmit clock) output to the MAC reconciliation sublayer is a continuous clock that provides the timing reference for the transfer of the TX_EN, TXD, and TX_ER signals. s TX_EN (transmit enable) input from the MAC reconciliation sublayer to indicate nibbles are being presented on the MII for transmission on the physical medium. TX_ER (transmit coding error) transitions synchronously with respect to TX_CLK. If TX_ER is asserted for one or more clock periods, and TX_EN is asserted, the PHY will emit one or more symbols that are not part of the valid data delimiter set somewhere in the frame being transmitted.
AM79C874
15
PRELIMINARY s RXD (receive data) is a nibble (4 bits) of data that is sampled by the reconciliation sublayer synchronously with respect to RX_CLK. For each RX_CLK period which RX_DV is asserted, RXD[3:0] are transferred from the PHY to the MAC reconciliation sublayer. s RX_CLK (receive clock) output to the MAC reconciliation sublayer is a continuous clock (during LINK only) that provides the timing reference for the transfer of the RX_DV, RXD, and RX_ER signals. s RX_DV (receive data valid) input from the PHY to indicate the PHY is presenting recovered and decoded nibbles to the MAC reconciliation sublayer. To interpret a receive frame correctly by the reconciliation sublayer, RX_DV must encompass the frame starting no later than the Start-of-Frame delimiter and excluding any End-Stream delimiter. s RX_ER (receive error) transitions synchronously with respect to RX_CLK. RX_ER will be asserted for 1 or more clock periods to indicate to the reconciliation sublayer that an error was detected somewhere in the frame being received by the PHY. s CRS (carrier sense) is asserted by the PHY when either the transmit or receive medium is non-idle and deasserted by the PHY when the transmit and receive medium are idle. 7-Wire (GPSI) Mode 7-Wire (GPSI) mode uses the existing MII pins, but data is transferred only on TXD[0] and RXD[0]. This mode is used in a General Purpose Serial Interface (GPSI) configuration for 10BASE-T. If the GPIO[0] pin is LOW at the rising edge of reset, then GPSI mode is selected. For this configuration, TX_CLK runs at 10 MHz. When the cable is unplugged, 10TXCLK ceases operation. The MII pins that relate to 7-wire (GPSI) mode are shown in Table 1. The unused input pins in this mode should be tied to ground through a 1 kW resistor. The RPTR pin must be connected to GND.
MII Pin Name RX_ER CRS/10CRS 7-Wire (GPSI) Not used Carrier Sense Detect
Note: CRS ends one and one-half bit times after the last data bit. The effect is one or two dribbling bits on every packet. All MACs truncate packets to eliminate the dribbling bits. The only noticeable effect is that all CRC errors are recorded as framing errors. Use the TECH_SEL[2:0] to select the desired 10BASET operation. For example, to auto-negotiate between Full Duplex and Half Duplex at 10 Mbps, set ANEG=1 and TECH[2:0]=101. 5B Symbol Mode The purpose of the 5B Symbol mode is to provide a way for the MAC to do the 4B/5B encoding/decoding and scrambling/descrambling in 100 Mbps operation. This is useful in MAC similar to the Intel/DEC 21143 MAC. In 10 Mbps operation, the MII signals are not used. Instea d, th e Ne tPHY-1LP dev ic e operates as a 10BASE-T transceiver, providing received data to the MAC over a serial differential pair (see Pin Descriptions, PCSBP pin). The MAC uses two serial differential pairs to provide transmit data to the NetPHY-1LP device, where the two differential pairs are combined in the NetPHY-1LP device to compensate for inter-symbol interference on the twisted pair medium.
100BASE-X Block
The functions performed by the device include encoding of MII 4-bit data (4B/5B), decoding of received code groups (5B/4B), generating carrier sense and collision detect indications, serialization of code groups for transmission, de-serialization of serial data upon reception, mapping of transmit, receive, carrier sense, and collision at the MII interface, and recovery of clock from the incoming data stream. It offers stream cipher scrambling and descrambling capability for 100BASETX applications. I n t h e t r a n s m i t d a t a p a t h fo r 1 0 0 M b p s, t h e NetPHY-1LP transceiver receives 4-bit (nibble) wide data across the MII at 25 million nibbles per second. For 100BASE-TX applications, it encodes and scrambles the data, serializes it, and transmits an MLT-3 data stream to the media via an isolation transformer. For 100BASE-FX applications, it encodes and serializes the data and transmits a Pseudo-ECL (PECL) data stream to the fiber optic transmitter. See Figure 1. In the receive data path for 100 Mbps, the NetPHY-1LP transceiver receives an MLT-3 data stream from the network. For 100BASE-TX, it then recovers the clock from the data stream, de-serializes the data stream, and descrambles/decodes the data stream (5B/4B) before presenting it at the MII interface.
Table 1. MII Pins That Relate to 10 Mbps 7-Wire (GPSI) Mode
MII Pin Name TX_CLK/10TXCLK TXD[0]/10TXD TXD[3:1] TX_EN/10TXEN TX_ER RX_CLK/10RXCLK RXD[0] /10RXD RXD[3:1] COL/10COL 7-Wire (GPSI) Transmit Clock Transmit Serial Data Stream Not used Transmit Enable Not used Receive Clock Receive Serial Data Stream Not used Collision Detect
16
AM79C874
PRELIMINARY
3.3 V
AM79C874 NetPHY-1LP
69 TEST1/FXR+ TEST0/FXRTEST3/SDI+ 183 183 3.3 V 130 130 130 69 69 0.1 F 0.1 F
HFBR/HFCT-5903 3.3 V MT-RJ
5 RD+ 4 RD3 SD+
69 FXTFXT+ FX_SEL 1 k 183
10 TD9 TD+
183
22235I-3
Figure 1. FXT and FXR Termination for 100BASE-FX
For 100BASE-FX operation, the NetPHY-1LP device receives a PECL data stream from the fiber optic transceiver and decodes that data stream. The 100BASE-X block consists of the following subblocks: Transmit Process Receive Process 4B/5B Encoder and Decoder Scrambler/Descrambler Link Monitor Far End Fault Generation and Detection & CodeGroup Generator -- MLT-3 encoder/decoder with Adaptive Equalization -- Baseline Restoration -- Clock Recovery Transmit Process The transmit process generates code-groups based on the transmit control and data signals on the MII. This process is also responsible for frame encapsulation into a Physical Layer Stream, generating the collision signal based on whether a carrier is received simultaneously during transmission and generating the Carrier Sense CRS and Collision COL signals at the MII. The transmit process is implemented in compliance with the -- -- -- -- -- --
transmit state diagram as defined in Clause 24 of the IEEE 802.3u specification. The NetPHY-1LP device transmit function converts synchronous 4-bit data nibbles from the MII to a 125Mbps differential serial data stream. The entire operation is synchronous to a 25-MHz clock and a 125-MHz clock. Both clocks are generated by an on-chip PLL clock synthesizer that is locked to an external 25-MHz clock source. In 100BASE-FX mode, the NetPHY-1LP device will bypass the scrambler. The output data is an NRZI PECL signal. This PECL level signal will then drive the Fiber transmitter. Receive Process The receive path includes a receiver with adaptive equalization and DC restoration, MLT-3-to-NRZI conversion, data and clock recovery at 125-MHz, NRZI-toNRZ conversion, Serial-to-Parallel conversion, descrambling, and 5B to 4B decoding. The receiver circuit starts with a DC bias for the differential RX inputs, follows with a low-pass filter to filter out high-frequency noise from the transmission channel media. An energy detect circuit is also added to determine whether there is any signal energy on the media. This is useful in the power-saving mode. (See the description in Power
AM79C874
17
PRELIMINARY Savings Mechanisms section). All of the amplification ratio and slicer thresholds are set by the on-chip bandgap reference. In 100BASE-FX mode, signal will be received through a PECL receiver, and directly passed to the clock recovery for data/clock extraction. In FX mode, the scrambler/descrambler cipher will be bypassed. 4B/5B Encoder/Decoder The 100 Mbps process in the NetPHY-1LP device uses the 4B/5B encoding scheme as defined in IEEE 802.3, Section 24. This scheme converts between raw data on the MII and encoded data on the media pins. The encoder converts raw data to the 4B/5B code. It also inserts the stream boundary delimiters (/J/K/ and /T/R/) at the beginning and end of the data stream as appropriate. The decoder converts between encoded data on the media pins and raw data on the MII. It also detects the stream boundary delimiters to help determine the start and end of packets. The code-group mapping is defined in Table 2. The 4B/5B encoding is bypassed when MII Register 21, bit 1 is set to "1", or the PCSBP pin (pin 1) is strapped high. Scrambler/Descrambler The 4B/5B encoded data has repetitive patterns which result in peaks in the RF spectrum large enough to keep the system from meeting the standards set by regulatory agencies such as the FCC. The peaks in the radiated signal are reduced significantly by scrambling the transmitted signal. Scramblers add the output of a random generator to the data signal. The resulting signal has fewer repetitive data patterns. After reset, the scrambler seed in each port will be set to the PHY address value to help improve the EMI performance of the device. The scrambled data stream is descrambled at the receiver by adding it to the output of another random generator. The receiver's random generator uses the same function as the transmitter's random generator. In 100BASE-TX mode, all 5-bit transmit data streams are scrambled as defined by the TP-PMD Stream Cipher function in order to reduce radiated emissions on the twisted pair cable. The scrambler encodes a plain text NRZ bit stream using a key stream periodic sequence of 2047 bits generated by the recursive linear function: X[n] = X[n-11] + X[n-9] (modulo 2) The scrambler reduces peak emissions by randomly spreading the signal energy over the transmit frequency range, thus eliminating peaks at a single frequency. When MII Register 21, bit 2 is set to "1," the data scrambling function is disabled and the 5-bit data stream is clocked directly to the device's PMA sublayer. Link Monitor Signal levels are detected through a squelch detection circuit. A signal detect (SD) circuit following the equalizer is asserted high whenever the peak detector senses a post-equalized signal with a peak-to-ground voltage level larger than 400 mV. This is approximately 40 percent of the normal signal voltage level. In addition, the energy level must be sustained longer than 2 ms in order for the signal detect to be asserted. It gets de-asserted approximately 1 ms after the energy level is consistently less than 300 mV from peak-to-ground. The link signal is forced to low during a local loopback operation (i.e., when MII Register 0, bit 14, Loopback is asserted) and forced to high when a remote loopback is taking place (i.e., when MII Register 21, bit 3, EN_RPBK, is set). In 100BASE-TX mode, when no signal or an invalid signal is detected on the receive pair, the link monitor will enter in the "link fail" state where only the scrambled idle code will be transmitted. When a valid signal is detected for a minimum period of time, the link monitor will then enter the link pass state when transmit and receive functions are entered. In 100BASE-FX mode, the external fiber-optic receiver performs the signal energy detection function and communicates this information directly to the NetPHY-1LP device through the SDI+ pin.
18
AM79C874
PRELIMINARY Table 2. Code-Group Mapping
MII (TXD[3:0]) 0000 0001 0010 0011 0100 0101 0 1 10 0111 1000 1001 1010 1011 1100 1101 1110 1111 Undefined 0101 0101 Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Undefined Name 0 1 2 3 4 5 6 7 8 9 A B C D E F I J K T R H V V V V V V V V V V PCS Code-Group 11110 01001 10100 10101 01010 01011 01110 01111 10010 10011 10110 10111 11010 11011 11100 11101 11111 11000 10001 01101 00111 00100 00000 00001 00010 00011 00101 00110 01000 01100 10000 11001 Interpretation Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data 8 Data 9 Data A Data B Data C Data D Data E Data F IDLE; used as inter-Stream fill code Start-of-Stream Delimiter, Part 1 of 2; always used in pairs with K Start-of-Stream Delimiter, Part 2 of 2; always used in pairs with J End-of-Stream Delimiter, Part 1 of 2; always used in pairs with R End-of-Stream Delimiter, Part 2 of 2; always used in pairs with T Transmit Error; used to force signaling errors Invalid Code Invalid Code Invalid Code Invalid Code Invalid Code Invalid Code Invalid Code Invalid Code Invalid Code Invalid Code
AM79C874
19
PRELIMINARY MLT-3 This block is responsible for converting the NRZI data stream from the PDX block to the MLT-3 encoded data stream. The effect of MLT-3 is the reduction of energy on the copper media (TX or FX cable) in the critical frequency range of 1 MHz to 100 MHz. The receive section of this block is responsible for equalizing and amplifying the received data stream and link detection. The adaptive equalizer compensates for the amplitude and phase distortion due to the cable. MLT-3 is a tri-level signal. All transitions are between 0 V and +1 V or 0 V and -1 V. A transition has a logical value of 1 and a lack of a transition has a logical value of 0. The benefit of MLT-3 is that it reduces the maximum frequency over the data line. The bit rate of TX data is 125 Mbps. The maximum frequency (using NRZI) is half of 62.5 MHz. MLT-3 reduces the maximum frequency to 31.25 MHz. A data signal stream following MLT-3 rules is illustrated in Figure 2. The data stream is 1010101. receive signals. The traces from the transformer to the NetPHY-1LP device should have a controlled impedance as a differential pair of 100 ohms. The same is true between the transformer and the RJ-45 connector. The TX pins can be connected to the media via either a 1:1 transformer or a 1.25:1 transformer. The 1.25:1 ratio provides a 20% transmit power savings over the 1:1 ratio. Refer to Figure 3. Adaptive Equalizer The NetPHY-1LP device is designed to accommodate a maximum cable length of 140 meters UTP CAT-5 cable. 140 meters of UTP CAT-5 cable has an attenuation of 31 dB at 100 MHz. The typical attenuation of a 100 meter cable is 21 dB. The worst case attenuation is around 24-26 dB defined by TP-PMD. The amplitude and phase distortion from the cable will cause intersymbol interference (ISI) which makes clock and data recovery impossible. The adaptive equalizer is made by closely matching the inverse transfer function of the twist-pair cable. This is a variable equalizer that changes its equalizer frequency response in accordance to cable length. The cable length is estimated based on comparisons of incoming signal strength against some of the known cable characteristics. The equalizer has a monotonical frequency response, and tunes itself automatically for any cable length to compensate for the amplitude and phase distortion incurred from the cable. Baseline Wander Compensation The 100BASE-TX data stream is not always DC balanced. The transformer blocks the DC component of the incoming signal, thus the DC offset of the differential receive inputs can wander. The shift in the signal levels, coupled with non-zero rise and fall times of the serial stream can cause pulse-width distortion. This creates jitter and a possible increase in error rates. Therefore, a DC restoration circuit is needed to compensate for the attenuation of the DC component. The NetPHY-1LP device implements a patentpending DC restoration circuit. Unlike the traditional implementation, it does not need the feedback information from the slicer and clock recovery circuit. This not only simplifies the system/circuit design, but also eliminates any random/systematic offset on the receive path. In 10BASE-T and 100Base-FX modes, the baseline wander correction circuit is not required and therefore will be bypassed.
1
0
1
0
1
0
1
8 ns
MLT-3
22235I-4
Figure 2. MLT-3 Waveform
The TX drivers convert the NRZI serial output to MLT-3 format. The RX receivers convert the received MLT-3 signals to NRZI. The transmit and receive signals will be compliant with IEEE 802.3u, Section 25. The required signals (MLT-3) are described in detail in ANSI X3.263:1995 TP-PMD Revision 2.2 (1995). The NetPHY-1LP device provides on-chip filtering. External filters are not required for either the transmit or
20
AM79C874
PRELIMINARY
VDD Isolation Transformer with common-mode chokes 1:1 or 1.25:1
RJ45 Connector
(Note 1)
(Note 1)
TX+
TX0.1 F 75 RX+ 1:1 75 75
(8) (7) TX+ (1) (5) (4) TX- (2)
RX+ (3) RX- (6) (Note 2)
RX(Note 2)
0.1 F
75
0.1 F
470 pF, 2 kV
(chassis ground)
Notes: 1. 49.9 W if a 1:1 isolation transformer is used or 78.1 W if a 1.25:1 isolation transformer is used. 2. 49.9 W is normal, but 54.9 W can be used for extended cable length operation.
22235I-5
Figure 3. Clock/Data Recovery
TX and RX Termination for 100BASE-TX and 10BASE-T the APLL switches back to lock with TX_CLK, thus providing a continuously running RX_CLK. The recovered data is converted from NRZI-to-NRZ and then to a 5-bit parallel format. The 5-bit parallel data is not necessarily aligned to 4B/5B code-group's symbol boundary. The data is presented to PCS at receive data register output, gated by the 25-MHz RX_CLK. PLL Clock Synthesizer The NetPHY-1LP device includes an on-chip PLL clock synthesizer that generates a 125 MHz and a 25 MHz clock for the 100BASE-TX or a 100 MHz and 20 MHz clock for the 10BASE-T and Auto-Negotiation operations. Only one external 25 MHz crystal or a signal source is required as a reference clock. After power-on or reset, the PLL clock synthesizer is defaulted to generating the 20 MHz clock output and will stay active until the 100BASE-X operation mode is selected.
The equalized MLT-3 signal passes through a slicer circuit which then converts it to NRZI format. The NetPHY-1LP device uses an analog phase-locked loop (APLL) to extract clock information from the incoming NRZI data. The extracted clock is used to re-time the data stream and set the data boundaries. The transmit clock is locked to the 25-MHz clock input, while the receive clock is locked to the incoming data streams. When initial lock is achieved, the APLL switches to lock to the data stream, extracts a 125 MHz clock from it and use that for bit framing to recover data. The recovered 125 MHz clock is also used to generate the 25 MHz RX_CLK. The APLL requires no external components for its operation and has high noise immunity and low jitter. It provides fast phase align (lock) to data in one transition and its data/clock acquisition time after power-on is less than 60 transitions. The APLL can maintain lock on run-lengths of up to 60 data bits in the absence of signal transitions. When no valid data is present, i.e., when the SD is de-asserted,
AM79C874
21
PRELIMINARY
10BASE-T Block
The NetPHY-1LP transceiver incor porates the 10BASE-T physical layer functions, including clock recovery (ENDEC), MAUs, and transceiver functions. The NetPHY-1LP transceiver receives 10-Mbps data from the MAC, switch, or repeater across the MII at 2.5 million nibbles per second (parallel), or 10 million bits per second (serial). It then Manchester encodes the data before transmission to the network. Refer to Figure 4 for the 10BASE-T transmit and receive data paths.
directly to a standard transformer. External filtering modules are not needed Twisted Pair Receive Process In 10BASE-T mode, the signal first passes through a third order Elliptical filter, which filters all the noise from the cable, board, and transformer. This eliminates the need for a 10BASE-T external filter. A Manchester decoder and a Serial-to-Parallel converter then follow to generate the 4-bit nibble in MII mode. RX+ ports are differential twisted-pair receivers. When properly terminated, each RX+ port meets the electrical requirements for 10BASE-T receivers as specified in IEEE 802.3, Section 14.3.1.3. Each receiver has internal filtering and does not require external filter modules or common mode chokes. Signals appearing at the RX differential input pair are routed to the internal decoder. The receiver function meets the propagation delays and jitter requirements specified by the 10BASE-T standard. The receiver squelch level drops to half its threshold value after unsquelch to allow reception of minimum amplitude signals and to mitigate carrier fade in the event of worst case signal attenuation and crosstalk noise conditions. Twisted Pair Interface Status The NetPHY-1LP transceiver will power up in the Link Fail state. The Auto-Negotiation algorithm will apply to allow it to enter the Link Pass state. A link-pulse detection circuit constantly monitors the RX pins for the presence of valid link pulses. In the Link Pass state, receive activity which passes the pulse width/amplitude requirements of the RX inputs cause the PCS Control block to assert Carrier Sense (CRS) signal at the MII interface. Collision Detect Function Simultaneous activity (presence of valid data signals) from both the internal encoder transmit function and the twisted pair RX pins constitutes a collision, thereby causing the PCS Control block to assert the COL pin at the MII. Collisions cause the PCS Control block to assert the Carrier Sense (CRS) and Collision (COL) signals at the MII. In the Link Fail state, this block would cause the PCS Control block to de-assert Carrier Sense (CRS) and Collision (COL). Jabber Function The Jabber function inhibits the 10BASE-T twisted pair transmit function of the NetPHY-1LP transceiver device if the TX circuits are active for an excessive period (20-150 ms). This prevents one port from disrupting the network due to a stuck-on or faulty transmitter condition. If the maximum transmit time is exceeded, the data path through the 10BASE-T transmitter circuitry is disabled (although Link Test pulses will continue to be
Clock
Data
Clock
Data
Manchester Encoder
Manchester Decoder
Loopback (Register 0)
Squelch Circuit
TX Driver
RX Driver
TX
RX
22235I-6
Figure 4.
10BASE-T Transmit /Receive Data Paths
Twisted Pair Transmit Process In 10BASE-T mode, Manchester code will be generated by the 10BASE-T core logic, which will then be synthesized through the output waveshaping driver. This will help reduce any EMI emission, eliminating the need for an external filter. Data transmission over the 10BASE-T medium requires use of the integrated 10BASE-T MAU and uses the differential driver circuitry on the TX pins. TX is a differential twisted-pair driver. When properly terminated, TX meets the transmitter electrical requirements for 10BASE-T transmitters as specified in IEEE 802.3, Section 14.3.1.2. The load is a twisted pair cable that meets IEEE 802.3, Section 14.4. The TX signal is filtered on the chip to reduce harmonic content per Section 14.3.2.1 (10BASE-T). Since filtering is performed in silicon, TX can be connected
22
AM79C874
PRELIMINARY sent). The PCS Control block also asserts the COL pin at the MII and sets the Jabber Detect bit in MII Register 1. Once the internal transmit data stream from the MENDEC stops, an unjab time of 250-750 ms will elapse before this block causes the PCS Control block to de-assert the COL indication and re-enable the transmit circuitry. When jabber is detected, this block causes the PCS control block to assert the COL pin and allows the PCS Control block to assert or de-assert the CRS pin to indicate the current state of the RX pair. If there is no receive activity on RX, this block causes the PCS Control block to assert only the COL pin at the MII. If there is RX activity, this block causes the PCS Control block to assert both COL and CRS at the MII. The Jabber function can be disabled by setting MII Register 21, bit 12. Reverse Polarity Detection and Correction Proper 10BASE-T receiver operation requires that the differential input signal be the correct polarity. That is, the RX+ line is connected to the RX+ input pin, and the RX- line is connected to the RX- input pin. Improper setup of the external wiring can cause the polarity to be reversed. The NetPHY-1LP receiver has the ability to detect the polarity of the incoming signal and compensate for it. Thus, the proper signal will appear on the MDI regardless of the polarity of the input signals. The internal polarity detection and correction circuitry is set during the reception of the normal link pulses (NLP) or packets. The receiver detects the polarity of the input signal on the first NLP. It locks the polarity correction circuitry after the reception of two consecutive packets. The state of the polarity correction circuitry is locked as long as link is established. enabled or disabled by hardware (ANEGA, pin 56) or software (MII Register 0, bit 12) control (see Table 3). The NetPHY-1LP device will automatically choose its mode of operation by advertising its abilities and comparing them with those received from its link partner whenever Auto-Negotiation is enabled. The content of MII Register 4 is sent to the link partner during Auto-Negotiation, coded in Fast Link Pulses (FLPs). MII Register 4, bits 8:5 reflect the state of the TECH_SEL[2:0] pins after reset. After reset, software can change any of these bits from 1 to 0 and back to 1, but not from 0 to 1 via the management interface. Therefore, hardware settings have priority over software. A write to Register 4 does not cause the device to restart Auto-Negotiation. When Auto-Negotiation is enabled, the NetPHY-1LP device sends FLP during the one of the following conditions: (a) power on, (b) link loss, or (c) restart command. At the same time, the device monitors incoming data to determine its mode of operation. When the device receives a burst of FLPs from its link partner with three identical link code words (ignoring acknowledge bit), it stores these code words in MII Register 5 and waits for the next three identical code words. Once the device detects the second code word, it will configure itself to the highest technology that is common to both ends. The technology priorities are: (1) 100BASE-TX, full-duplex, (2) 100BASE-TX, half-duplex, (3) 10BASET, full-duplex, and (4) 10BASE-T half-duplex. Parallel Detection The parallel detection circuit is enabled as soon as either 10BASE-T idle or 100BASE-TX idle is detected. The mode of operation gets configured based on the technology of the incoming signal. The NetPHY-1LP device can also check for a 10BASE-T NLP or 100BASE-TX idle symbol. If either is detected, the device automatically configures to match the detected operating speed in half-duplex mode. This ability allows the device to communicate with legacy 10BASE-T and 100BASE-TX systems.
Auto-Negotiation and Miscellaneous Functions
Auto-Negotiation The NetPHY-1LP device has the ability to negotiate its mode of operation over the twisted pair using the AutoNegotiation mechanism defined in Clause 28 of the IEEE 802.3u specification. Auto-Negotiation may be
AM79C874
23
PRELIMINARY Table 3. Speed and Duplex Capabilities
ANEGA 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Tech[2] 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 Tech[1] 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 Tech[0] 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Speed Yes (Note 1) No No No Yes (Note 1) No No No Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 2) Duplex Yes (Note 1) No No No Yes (Note 1) No No No Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) Yes (Note 3) ANEG-EN Capabilities/ANEG No No No No No No No No Yes (Note 2) Yes (Note 2) Yes (Note 2) Yes (Note 2) Yes (Note 2) Yes (Note 2) Yes (Note 2) Yes (Note 2) All Capabilities 10HD 100HD 100HD All Capabilities 10FD 100FD 100FD No Capabilities, ANEG 10HD, ANEG 100HD, ANEG 100HD, 10HD, ANEG No Capabilities, ANEG 10FD/HD, ANEG 100FD/HD, ANEG All Capabilities, ANEG (Hardwired on Board) (Changeable in MII Register 0)
Notes: 1. MII Register 0 (speed and duplex bits) must be set by the MAC to achieve a link. 2. The advertised abilities in MII Register 4 cannot exceed the abilities of MII Register 1. Auto-Negotiation should always remain enabled. 3. When Auto-Negotiation is enabled, these bits can be written but will be ignored by the PHY.
Far-End Fault Auto-Negotiation provides a remote fault capability for detecting asymmetric link failure. Since 100Base-FX systems do not use Auto-Negotiation, an alternative, in-band signaling scheme, Far-End Fault is used to signal remote fault conditions. Far-End Fault is a stream of 63 consecutive 1s followed by one logic 0. This pattern is repeated three times. A Far-End Fault will be signaled under three conditions: (1) when no activity is received from the link partner, (2) when the clock recovery circuit detects signal error or PLL lock error, and (3) when the management entity sets the transmit FEF bit (MII Register 21, bit 7). The Far-End Fault mechanism defaults to enable 100BASE-FX mode and disable 100BASE-TX and 10BASE-T modes, and may be controlled by software after reset. SQE (Heartbeat) When the SQE test is enabled, a COL signal with a 515 bit time pulse will be issued after each transmitting packet. SQE is enabled and disabled via MII Register 16, bit 11. Loopback Operation A local loopback and remote loopback are provided for testing. They can be enabled by writing to either MII
Register 0, bit 14 (Loopback) or MII Register 21, bit 3 (EN_RPBK). The local loopback routes transmitted data at the output of NRZ-to-NRZI conversion module back to the receiving path's clock and data recovery module for connection to PCS in 5 bits symbol format. This loopback is used to check all the connections at the 5-bit symbol bus side and the operation of analog phase locked loop. In local loopback, the SD output is forced to logic one and TX outputs are tristated. During local loopback, a 10-Mbps link is sent to the link partner. In either 100BASE-TX or 10BASE-T loopback mode, the link for 10 Mbps is forced (Register 21, bit 14) and is seen externally. If packets are transmitted from the Device Under Test (DUT), the link between the DUT and link partner is lost. Ceasing transmission causes the link to go back up. In remote loopback, incoming data passes through the equalizer and clock recovery, then loop back to NRZI/ MLT3 conversion module and out to the driver. This loopback is used to check the device's connection on the media side and the operation of its internal adaptive equalizer, phase-locked loop, and digital wave shape synthesizer. During remote loopback, signal detect (SD) output is forced to logic zero. Note that remote loopback operates only in 100BASE-TX mode.
24
AM79C874
PRELIMINARY External loopback can be accomplished using an external loopback cable with TX connected to RX. External loopback works for both 10 Mbps and 100 Mbps after setting Register 0, bit 8 to force full duplex and bit 13 to set the speed. Reset The NetPHY-1LP device can be reset in the three following ways: 1. During initial power on (with internal power on reset circuit). 2. At hardware reset. A logic low signal of 10 ms pulse width applied to the RST pin. 3. At software reset. Write a 1 to MII Register 0, bit 15. The polarity of the LED drivers (Active-LOW or ActiveHIGH) is set at the rising edge of RST. If the pin is LOW at the rising edge of RST, it becomes an active-HIGH driver. If it is HIGH at the rising edge of RST, it becomes an active-LOW driver. Proper configuration requires pull-up or pull-down resistors. As shown in the Pin Description sections, each of the LED/Configuration pins has internal pull-up resistors. If the pin's LED functionality is not used, the pin may still need to be terminated via an external pulldown resistor according to the desired configuration. The resistor value is not critical and can be in the range of 1 kW to 10 kW. If the corresponding LED is used, the terminating resistor must be placed in parallel with the LED. Suggested LED connection diagrams simplifying the board design are shown in Figure 5 (standard) and Figure 6 (advanced). The value of the series resistor (RL) should be selected to ensure sufficient illumination of the LED. It is dependent on the rating of the LED.
LED Port Configuration
The NetPHY-1LP device has several pins that are used for both device configuration and LED drivers. These pins set the configuration of the device on the rising edge of RST and thereafter indicate the state of the respective port. See Table 4 for standard LED selections and Table 5 for advanced LED selections.
Table 4. Standard LED Selections
MODE No Link 10HD-RX 10HD-TX 10HD-COL 10FD-RX 10FD-TX 10FD-RX+TX 100HD-RX 100HD-TX 100HD-COL 100FD-RX 100FD-TX 100FD-RX+TX LEDSDP[0] 0 0 0 0 0 0 0 1 1 1 1 1 1 LEDSDP[1] 0 1 1 1 1 1 1 0 0 0 0 0 0 LEDLNK 0 1 1 1 1 1 1 1 1 1 1 1 1 LEDDPX 0 0 0 0 1 1 1 0 0 0 1 1 1 LEDTX 0 0 T T 0 T T 0 T T 0 T T LEDRX 0 T 0 T T 0 T T 0 T T 0 T LEDCOL 0 0 0 T 0 0 0 0 0 T 0 0 0
Notes: 1. 1 means on (logic level low since active low). 2. 0 means off (logic level high since active low). 3. T means toggles (will end at logic level high).
AM79C874
25
PRELIMINARY
LED 330 100 Mbps LEDSPD[0] LED 330 10 Mbps LEDSP[1] LED 330 Collision LEDCOL LED 330 Duplex LEDDPX LED 330 Transmit LEDTX LED 330 Receive LEDRX LED 330 Link (Note 1) LEDLNK LED 330 Link (Note 2) LEDLNK
VCC
VCC
VCC
VCC
VCC
VCC
VCC
22235I-7
Notes: 1. Use for non 7-wire interface configurations. 2. Use for 7-wire interface configurations.
Figure 5. Standard LED Configuration Table 5.
MODE No Link 10BT Half Duplex 10BT Half Activity 10BT Full Duplex 10BT Full Activity 100BT Half Duplex 100BT Half Activity 100BT Full Duplex 100BT Full Activity LEDBTX/ LEDBTA (Pin 44) 0 1 Flash (Note 1) 0 0 0 0 0 0
Advanced LED Selections
LEDTX/ LEDBTB (Pin 47) 0 0 0 1 Flash (Note 2) 0 0 0 0 LEDBT/ LEDTXA (Pin 57) 0 0 0 0 0 1 Flash (Note 1) 0 0 LEDFDX/ LEDTXB (Pin 58) 0 0 0 0 0 0 0 1 Flash (Note 2)
Notes: 1. LED flashes for RX and TX activity. 2. LED flashes for RX activity.
3. 0 means logic level low at the pin. 4. 1 means logic level high at the pin.
26
AM79C874
PRELIMINARY
VCC LED Receive LEDRX 5K LEDBTB VCC LED Collision LEDCOL VCC LED Link (Note 1) LEDLNK 330 LEDTXA 330 330 LEDBTA
300 Dual-Color LED
10BASE-T LED Indicator
300 Dual-Color LED
LED Link (Note 2) LEDLNK
330
LEDTXB 100BASE-TX LED Indicator
Notes: 1. Use for non 7-wire interface configurations. 2. Use for 7-wire interface configurations.
22235I-8
Figure 6. Advanced LED Configuration
Power Savings Mechanisms
The power consumption of the device is significantly reduced by its built-in power down features. Separate power supply lines are also used to power the 10BASE-T circuitry and the 100BASE-TX circuitry. Therefore, the two modes of operation can be turnedon and turned-off independently. Whenever the NetPHY-1LP device is set to operate in a 100BASE-TX mode, the 10BASE-T circuitry is powered down, and when in 10BASE-T mode, the 100BASE-TX circuitry is powered down. The NetPHY-1LP device offers the following power management: Selectable Transformer, Power Down, Unplugged, and Idle. Selectable Transformer The TX outputs can drive either a 1:1 transformer or a 1.25:1 transformer. The latter can be used to reduce transmit power further. The current at the TX pins for a 1:1 ratio transformer is 40 mA for MLT-3 and 100 mA for 10BASE-T. Using the 1.25:1 ratio reduces the current to 30 mA for MLT-3 and 67 mA for 10BASE-T. The cost of using the 1.25:1 option is in impedance coupling. The reflected capacitance is increased by the square of the ratio (1.252 = 1.56). Thus, the reflected capacitance on the media side is roughly one and a half
times the capacitance on the board. Extra care in the layout to control capacitance on the board is required. Power Down Most of the NetPHY-1LP device can be disabled via the Power Down bit in MII Register 0, bit 11. Setting this bit will power down the entire device with the exception of the MDIO/MDC management circuitry. Unplugged The TX output driver limits the drive capability if the receiver does not detect a link partner within 4 seconds. This prevents "wasted" power. If the receiver detects the absence of a link partner, the transmitter is limited to transmitting normal link pulses. Any energy detected by the receiver enables full transmit and receive capabilities. The power savings is most notable when the port is unconnected. Typical power drops to one third of normal. Idle Wire This can be achieved by writing to MII Register 16, bit 0. During this mode, if there is no data other than idles coming in, the receive clock (RX_CLK) will turn off to save power for the attached controller. RX_CLK will resume operation one clock period prior to the assertion of RX_DV. The receive clock will again shut off 64 clock cycles after RX_DV gets deasserted. Typical power savings of 100 mW can be realized in some MACs.
AM79C874
27
PRELIMINARY
PHY CONTROL AND MANAGEMENT BLOCK (PCM BLOCK) Register Administration for 100BASE-X PHY Device
The management interface specified in Clause 22 of the IEEE 802.3u standard provides for a simple two wire, serial interface to connect a management entity and a managed PHY for the purpose of controlling the PHY and gathering status information. The two lines are Management Data Input/Output (MDIO), and Man-
agement Data Clock (MDC). A station management entity which is attached to multiple PHY entities must have prior knowledge of the appropriate PHY address for each PHY entity.
Description of the Methodology
The management interface physically transports management information across the MII. The information is encapsulated in a frame format as specified in Clause 22 of IEEE 802.3u draft standard and is shown in Table 6.
Table 6. Clause 22 Management Frame Format
PRE READ WRITE 1.1 1.1 ST 01 01 OP 10 01 PHYAD AAAAA AAAAA REGADD RRRRR RRRRR TA Z0 10 DATA D...........D D...........D IDLE Z Z
The PHYAD field, which is five bits wide, allows 32 unique PHY addresses. The managed PHY layer device that is connected to a station management entity via the MII interface has to respond to transactions addressed to the PHY address. A station management
entity attached to multiple PHYs, such as in a managed 802.3 Repeater or Ethernet switch, is required to have prior knowledge of the appropriate PHY address. See Table 7 and Figure 7.
Table 7. PHY Address Setting Frame Structure
PRE READ WRITE 1.1 1.1 ST 01 01 OP 10 01 PHYAD 00000 00000 REGADD RRRRR RRRRR TA Z0 10 DATA XXXXXXXXXPPAAAAA XXXXXXXXXPPAAAAA IDLE Z Z
MDC z MDIO (STA) z
MDIO (PHY)
z
z
z Idle
0
1
1
0
1
0
1
1
0
0
0
0
0
1
z TA
0
0
1
1
0
0
0
0
0
0
1
0
0
0
0
0
1
z Idle
Start
Opcode (Read)
PHY Address 16h, Port 2
Register Address MII Status, 1h
Register Data
Read Operation
MDC
MDIO z (STA)
z
z Idle
0
1
0
1
1
0
1
1
0
0
0
0
0
0
1 TA
0
0
1
1
0
0
0
0
1
0
0
0
0
0
0
0
0
z Idle
Start
Opcode (Write)
PHY Address 16h, Port 2
Register Address MII Control, 0h
Register Data
Write Operation
22235I-9
Figure 7. PHY Management Read and Write Operations
28
AM79C874
PRELIMINARY Bad Management Frame Handling The management block of the device can recognize management frames without preambles (preamble suppression). However, if it receives a bad management frame, it will go into a Bad Management Frame state. It will stay in this state and will not respond to any management frame without preambles until a frame with a full 32-bit preamble is received, then it will return to normal operation. A bad management frame is a frame that does not comply with the IEEE standard specification. It can be one with less than 32-bit preamble, with illegal OP field, etc. However, a frame with more than 32 preamble bits is considered to be a good frame. After a reset, the NetPHY-1LP device requires a minimum preamble of 32 bits before management data (MDIO) can be received. After that, the management data being received by the NetPHY-1LP device does not require a preamble.
REGISTER DESCRIPTIONS
The following registers given in Table 8 are supported (register addresses are in decimal). Table 8. Register Summary
Register Address (in Decimal) 0 1 2 3 4 5 6 7 8-15 16 17 18 19 20 21 22 23 24 25-31
Description MII Management Control Register MII Management Status Register PHY Identifier 1 Register PHY Identifier 2 Register Auto-Negotiation Advertisement Register Auto-Negotiation Link Partner Ability Register Auto-Negotiation Expansion Register Next Page Advertisement Register Reserved Miscellaneous Features Register Interrupt Control/Status Register Diagnostic Register Power Management & Loopback Register Reserved Mode Control Register Reserved Disconnect Counter Receive Error Counter Reserved
The Physical Address of the PHY is set using the pins defined as PHYAD[4:0]. These input signals are strapped externally and sampled as when reset goes high. The PHYAD pins can be reprogrammed via software.
Serial Management Registers
A detailed definition of each Serial Management register follows. The mode legend is shown in Table 9.
Table 9. Legend for Register Table
Type RW SC LL RO RC LH Description Readable and writable Self Clearing Latch Low until clear Read Only Cleared on the read operation Latch high until clear
AM79C874
29
PRELIMINARY MII Management Control Register (Register 0) Table 10. MII Management Control Register (Register 0)
Reg Bit Name Description 1 = PHY reset. 0 15 Reset 0 = Normal operation. This bit is self-clearing. 1 = Enable loopback mode. This will loopback TXD to RXD, thus it will ignore all the activity on the cable media. During loopback, a 10-Mbps link is sent to the link partner (Register 21, bit 14 is forced.) 0 = Disable Loopback mode. Normal operation. 0 13 Speed Select 1 = 100 Mbps, 0 = 10 Mbps. This bit will be ignored if Auto Negotiation is enabled (0.12 = 1). Refer to Table 3 to determine when this bit can be changed. 1 = Enable auto-negotiate process (overrides 0.13 and 0.8). 0 12 Auto-Neg Enable 0 = Disable auto-negotiate process. Mode selection is controlled via bit 0.8, 0.13 or through TECH[2:0] pins. Refer to Table 3 to determine when this bit can be changed. 1 = Power down. The NetPHY-1LP device will shut off all blocks except for MDIO/MDC interface. Setting PWRDN pin to high will achieve the same result. 0 = Normal operation. 1 = Electrically isolate the PHY from MII. However, PHY is still able to respond to MDC/MDIO. The default value of this bit depends on ISODEF pin, i.e., ISODEF=1, ISO bit will set to 1, & ISODEF=0, ISO bit will set to 0. 0 = Normal operation. 0 9 Restart AutoNegotiation Duplex Mode 1 = Restart Auto-Negotiation process. 0 = Normal operation. 1 = Full duplex, 0 = Half duplex. Refer to Table 3 to determine when this bit can be changed. 1 = Enable collision test, which issues the COL signal in response to the assertion of TX_EN signal. Collision test is disabled if PCSBP pin is high. Collision test is enabled regardless of the duplex mode. 0 = disable COL test. 0 6:0 Reserved Write as 0, ignore when read. RW 0 RW/SC 0 Set by TECH[2:0] pins Set by ISODEF pin RW Set by ANEGA pin RW Set by TECH[2:0] pins RW/SC 0 Read/ Write Default
0
14
Loopback
RW
0
0
11
Power Down
RW
0
0
10
Isolate
RW
0
8
RW
0
7
Collision Test
RW
0
30
AM79C874
PRELIMINARY MII Management Status Register (Register 1) Table 11. MII Management Status Register (Register 1)
Reg 1 Bit 15 Name 100BASE-T4 Description 1 = 100BASE-T4 able. 0 = Not 100BASE-T4 able. Read/ Write RO Default 0 set by TECH[2:0] pins set by TECH[2:0] pins set by TECH[2:0] pins set by TECH[2:0] pins 0 1
1
14
100BASE-TX Full 1 = 100BASE-TX Full Duplex. Duplex 0 = No 100BASE-TX Full Duplex ability. 100BASE-TX Half 1 = 100BASE-TX Half Duplex. Duplex 0 = No TX half-duplex ability. 10BASE-T Full Duplex 10BASE-T Half Duplex Reserved Management Frame Preamble Suppression Auto-Negotiation Complete 1 = 10BASE-T Full Duplex. 0 = No 10BASE-T Full Duplex ability. 1 = 10BASE-T Half Duplex. 0 = No 10BASE-T ability. Ignore when read. The device accepts management frames that do not have a preamble after receiving a management frame with a 32-bit or longer preamble. 1 = Auto-Negotiation process completed. Registers 4, 5, and 6 are valid after this bit is set. 0 = Auto-Negotiation process not completed. 1 = Remote fault condition detected. 0 = No remote fault. This bit will remain set until it is read via the management interface.
RO
1
13
RO
1
12
RO
1 1 1
11 10:7 6
RO RO RO
1
5
RO
0
1
4
Remote Fault
RO/LH
0
1
3
Auto-Negotiation Ability
1 = Able to perform Auto-Negotiation function; value is determined by ANEGA pin. 0 = Unable to perform Auto-Negotiation function. 1 = Link is established; however, if the NetPHY-1LP device link fails, this bit will be cleared and remain cleared until Register 1 is read via management interface. 0 = link is down. 1 = Jabber condition detected. 0 = No Jabber condition detected. 1 = Extended register capable. This bit is tied permanently to one.
RO
set by ANEGA pin
1
2
Link Status
RO/LL
0
1 1
1 0
Jabber Detect Extended Capability
RO/LH RO
0 1
PHY Identifier 1 Register (Register 2) Table 12. PHY Identifier 1 Register (Register 2)
Reg 2 15 Name OUI Description Composed of the 3rd through 18th bits of the Organizationally Unique Identifier (OUI), respectively. Read/ Write RO Default 0022(H)
AM79C874
31
PRELIMINARY PHY Identifier 2 Register (Register 3) Table 13. PHY Identifier 2 Register (Register 3)
Reg 3 3 3 Bit Name Description Assigned to the 19th through 24th bits of the OUI. Six-bit manufacturer's model number. Four-bit manufacturer's revision number. Read/ Write RO RO RO Default 010101 100001 1011
15:10 OUI 9:4 3:0 Model Number Revision Number
Auto-Negotiation Advertisement Register (Register 4) Table 14.
Reg 4 4 4 4 Bit 15 14 13 12:11 Name Next Page Acknowledge Remote Fault Reserved
Auto-Negotiation Advertisement Register (Register 4)
Description 1 = Next Page enabled. 0 = Next Page disabled. This bit will be set internally after receiving three consecutive and consistent FLP bursts. 1 = Remote fault supported. 0 = No remote fault. For future technology. Full Duplex Flow Control: Read/ Write RW RO RW RW Default 0 0 0 0
4
10
FDFC
1 = Advertise that the DTE(MAC) has implemented both the optional MAC control sublayer and the pause function as specified in clause 31 and annex 31 B of 802.3u. 0 = No MAC-based full duplex flow control.
RW
0
4
9
100BASE-T4
NetPHY-1LP device does not support 100BASE-T4 function, i.e., this bit ties to zero. 1 = 100BASE-TX Full Duplex.
RO
0 set by TECH [2:0] pins set by TECH[2:0] pins set by TECH[2:0] pins set by TECH[2:0] pins 00001
4
8
100BASE-TX Full Duplex
0 = No 100BASE-TX Full Duplex ability. Default is set by Register 1.14. 1 = 100BASE-TX Half Duplex.
RW
4
7
100BASE-TX Half Duplex
0 = No 100BASE-TX Half Duplex capability. Default is set by Register 1.13 1 = 10 Mbps Full Duplex.
RW
4
6
10BASE-T Full Duplex
0 = No 10 Mbps Full Duplex capability. Default is set by Register 1.12. 1 = 10 Mbps Half Duplex.
RW
4
5
10BASE-T Half Duplex Selector Field
0 = No 10 Mbps Half Duplex capability Default is set by Register 1.11.
RW
4
4:0
[00001] = IEEE 802.3.
RO
32
AM79C874
PRELIMINARY Auto-Negotiation Link Partner Ability Register in Base Page Format (Register 5) Table 15. Auto-Negotiation Link Partner Ability Register in Base Page Format (Register 5)
Reg 5 Bit 15 Name Next Page Description 1 = Next Page Requested by Link Partner 0 = Next Page Not Requested 1 = Link Partner Acknowledgement 0 = No Link Partner Acknowledgement 1 = Link Partner Remote Fault Request 0 = No Link Partner Remote Fault Request Reserved for Future Technology 1 = Link Partner supports Flow Control. 0 = Link Partner does not support Flow Control. 1 = Remote Partner is 100BASE-T4 Capable 0 = Remote Partner is not 100BASE-T4 Capable 1 = Link Partner is capable of 100BASE-TX Full Duplex 0 = Link Partner is Not Capable of 100BASE-TX Full Duplex 1 = Link Partner is Capable of 100BASE-TX Half Duplex 0 = Link Partner is Not Capable of 100BASE-TX Half Duplex 1 = Link Partner is capable of 10BASE-T Full Duplex 0 = Link Partner is Not Capable of 10BASE-T Full Duplex 1 = Link Partner is capable of 10BASE-T Half Duplex 0 = Link Partner is Not Capable of 10BASE-T Half Duplex Link Partner Selector Field RO RO 0 00001 RO 0 RO 0 RO 0 Read/ Write RO Default 0
5
14
Acknowledge
RO
0
5 5 5
13 12:11 10
Remote Fault Reserved Flow Control
RO RO RO
0
0
5
9
100BASE-T4
RO
0
5
8
100BASE-TX Full Duplex
5
7
100BASE-TX Half Duplex
5
6
10BASE-T Full Duplex
5 5
5 4:0
10BASE-T Half Duplex Selector Field
Auto-Negotiation Link Partner Ability Register in Next Page Format (Register 5) Table 16. Auto-Negotiation LInk Partner Ability Register in Next Page Format (Register 5)
Reg 5 Bit 15 Name Next Page Description 1 = Next Page Requested by Link Partner 0 = Next Page Not Requested 1 = Link Partner Acknowledgement 0 = No Link Partner Acknowledgement 1 = Link Partner message Page Request 0 = No Link partner Message Page Request 1 = Link Partner can Comply Next Page Request 0 = Link Partner cannot Comply Next Page Request Link Partner Toggle Link Partner's Message Code Read/ Write RO Default 0
5
14
Acknowledge
RO
0
5
13
Message Page
RO
0
5 5 5
12 11 10:0
Acknowledge 2 Toggle Message Field
RO RO RO
0 0 0
AM79C874
33
PRELIMINARY Auto-Negotiation Expansion Register (Register 6) Table 17. Auto-Negotiation Expansion Register (Register 6)
Reg 6 Bit 15:5 Name Reserved Parallel Detection Fault Description Ignore when read. 1 = Fault detected by parallel detection logic. This fault is due to more than one technology detecting concurrent link up conditions. This bit is cleared upon reading this register. 0 = No fault detected by parallel detection logic. 6 6 6 3 2 1 Link Partner Next Page Able Next Page Able Page Received 1 = Link partner supports next page function. 0 = Link partner does not support next page function. Next page is supported. This bit is permanently tied to 1. This bit is set when a new link code word has been received into the Auto-Negotiation Link Partner Ability Register. This bit is cleared upon reading this register. RO RO RO/LH 0 1 0 Read/ Write RO Default 0
6
4
RO/LH
0
6
0
Link Partner Auto- 1 = Link partner is auto-negotiation able. Negotiation Able 0 = Link partner is not auto-negotiation able.
RO
0
34
AM79C874
PRELIMINARY Auto-Negotiation Next Page Advertisement Register (Register 7) Table 18.
Reg Bit Name
Auto-Negotiation Next Page Advertisement Register (Register 7)
Description Next page indication: Read/ Write Default
7
15
NP
1 = Another Next Page desired. 0 = No other Next Page Transfer desired.
RW
0
7
14
Reserved
Ignore when read. Message page:
RO
0
7
13
MP
1 = Message page. 0 = Un-formatted page. Acknowledge 2:
RW
1
7
12
ACK2
1 = Will comply with message. 0 = Cannot comply with message. Toggle:
RW
0
7
11
TOG_TX
1 = Previous value of transmitted link code word equals to 0. 0 = Previous value of transmitted link code word equals to 1.
RW
0
17
10:0
CODE
Message/Un-formatted Code Field.
RW
001
Reserved Registers (Registers 8-15, 20, 22, 25-31) The NetPHY-1LP device contains reserved registers at addresses 8-15, 20, 22, 25-31. These registers should be ignored when read and should not be written at any time.
AM79C874
35
PRELIMINARY Miscellaneous Features Register (Register 16) Table 19. Miscellaneous Features Register (Register 16)
Reg 16 Bit 15 Name Repeater Description 1= Repeater mode, full-duplex is inactive, and CRS only responds to receive activity. SQE test function is also disabled. INTR will be active high if this register bit is set to 1. Pin requires an external pull-down resistor. INTR will be active low if this register bit is set to 0. Pin requires an external pull-up resistor. Write as 0, ignore when read. 1 = Disable 10BASE-T SQE testing. 16 11 SQE Test Inhibit 0 = Enable 10BASE-T SQE testing. A COL pulse is generated following the completion of a packet transmission. 1 = Enable normal loopback in 10BASE-T mode. 0 = Disable normal loopback in 10BASE-T mode. When GPIO_1 DIR bit is set to 1, this bit reflects the value of the GPIO[1] pin. When GPIO_1 DIR bit is set to 0, the value of this bit will be presented on the GPIO[1] pin. 1 = GPIO[1] pin is an input. 0 = GPIO[1] pin is an output. When GPIO_0 DIR bit is set to 1, this bit reflects the value of the GPIO[0] pin. When GPIO[0] DIR bit is set to 0, the value of this bit will be presented on the GPIO[0] pin. 1 = GPIO[0] pin is an input. 0 = GPIO[0] pin is an output. 1 = Disable auto polarity detection/correction. 0 = Enable auto polarity detection/correction. When Register 16.5 is set to 0, this bit will be set to 1 if reverse polarity is detected on the media. Otherwise, it will be 0. 16 4 Reverse Polarity When Register 16.5 is set to 1, writing a 1 to this bit will reverse the polarity of the transmitter. Note: Reverse polarity is detected either through eight inverted NLPs or through a burst of an inverted FLP. 16 3:1 Reserved Write as 0, ignore when read. Writing a 1 to this bit will shut off RX_CLK when incoming data is not present and only if there is LINK present. RX_CLK will resume activity one clock cycle prior to RX_DV going high, and shut off 64 clock cycles after RX_DV goes low. A 0 indicates that RX_CLK runs continuously during LINK whether data is received or not In loopback and PCS bypass modes, writing to this bit does not affect RX_CLK. Receive clock will be constantly active. RW 0 RO 0 RW 0 RW 0 Read/ Write RW Default Set by RPTR
16
14
INTR_LEVL
RW
0
16
13:12
Reserved
RW
0
16
10
10BASE-T Loopback GPIO_1 Data
RW
1
16
9
RW
0
16
8
GPIO_1 DIR
RW
1
16
7
GPIO_0 Data
RW
0
16
6
GPIO_0 DIR Auto polarity Disable
RW
1
16
5
RW
0
16
0
Receive Clock Control
36
AM79C874
PRELIMINARY Interrupt Control/Status Register (Register 17) Table 20. Interrupt Control/Status Register (Register 17)
Reg 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Name Jabber_IE Rx_Er_IE Page_Rx_IE PD_Fault_IE LP_Ack_IE Link_Not_OK_ IE R_Fault_IE ANeg_Comp_IE Jabber_Int Rx_Er_Int Page_Rx_Int PD_Fault_Int LP_Ack_Int Link_Not_OK Int R_Fault_Int A_Neg_Comp Int Description Jabber Interrupt Enable Receive Error Interrupt Enable Page Received Interrupt Enable Parallel Detection Fault Interrupt Enable Link Partner Acknowledge Interrupt Enable Link Status Not OK Interrupt Enable Remote Fault Interrupt Enable Auto-Negotiation Complete Interrupt Enable This bit is set when a jabber event is detected. This bit is set when RX_ER transitions high. This bit is set when a new page is received from link partner during Auto-Negotiation. This bit is set for a parallel detection fault. This bit is set when an FLP with the acknowledge bit set is received. This bit is set when link status switches from OK status to Not-OK (Fail or Ready). This bit is set when a remote fault is detected. This bit is set when Auto-Negotiation is complete. Read/ Write RW RW RW RW RW RW RW RW RC RC RC RC RC RC RC RC Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Note: * See Interrupt Source Table for bit assignments. Diagnostic Register (Register 18) Table 21. Diagnostic Register (Register 18)
Reg 18 18 Bit 15:12 11 Name Reserved DPLX Description Ignore when read. 1 = The result of Auto-Negotiation for Duplex is Full-duplex. 0 = The result of Auto-Negotiation for Duplex is Half-duplex. 1 = The result of Auto-Negotiation for data-rate arbitration is 100 Mbps. 0 = The result of Auto-Negotiation for data-rate arbitration is 10 Mbps. Operating in 100BASE-X mode: 1 = A valid signal has been received but the PLL has not necessarily locked. 0 = A valid signal has not been received. Operating in 10BASE-T mode: 1 = Manchester data has been detected. 0 = Manchester data has not been detected. 1 = Receive PLL has locked onto received signal for selected data-rate (10BASE-T or 100BASE-X). 0 = Receive PLL has not locked onto received signal. This bit remains set until it is read. Ignore when read. Read/ Write RO RO Default 0 0
18
10
Data Rate
RO
0
18
9
RX_PASS
RO
0
18
8
RX_LOCK
RO/RC
0
18
7:0
Reserved
RO
0
AM79C874
37
PRELIMINARY Power/Loopback Register (Register 19) Table 22.
Reg 19 Bit 14:7 Name Reserved Transmit transformer ratio selection: 1 = 1.25:1 19 6 TP125 0 = 1:1 The default value of this bit is controlled by reset-read value of pin 20. 1 = Enable advanced power saving mode. 0 = Disable advanced power saving mode 19 5 Low Power Mode Note: Under normal operating conditions, this mode should never be disabled. Power dissipation will exceed data sheet values, as circuitry for both 10 Mbps and 100 Mbps will be turned on. 1 = Enable test loopback. Data will be transmitted from MII interface to clock recovery and loopback to MII received data. 1 = Enable loopback. 0 = Normal operation. 1 = Enable link pulse loopback. 0 = Normal operation. 1 = In Auto-Negotiation test mode, send NLP instead of FLP in order to test NLP receive integrity. 0 = Sending FLP in Auto-Negotiation test mode. 1 = Reduce time constant for Auto-Negotiation timer. 0 = Normal operation. RW 0 RW 1 RW 0
Power/Loopback Register (Register 19)
Read/ Write RW Default 00
Description
19 19
4 3
Test Loopback Digital loopback
RW RW
0 0
19
2
LP_LPBK
RW
0
19
1
NLP Link Integrity Test
RW
0
19
0
Reduce Timer
38
AM79C874
PRELIMINARY Mode Control Register (Register 21) Table 23. Mode Control Register (Register 21)
Reg 21 21 Bit 15 14 Name Reserved
Force_Link_10
Description
Read/ Write RO
Default 0 0
1 = Force link up without checking NLP. Forced during local loopback. 0 = Normal Operation.
RW
21
13
Force_Link_100
1 = Ignore link in 100BASE-TX and transmit data. AutoNegotiation must be disabled at this time (pin 56 tied low). 0 = Normal Operation.
RW
0
21
12
Jabber Disable
1 = Disable Jabber function in PHY. 0 = Enable Jabber function in PHY. 1 = Enable 7-wire interface for 10BASE-T operation. This bit is useful only when the chip is not in PCS bypass mode. 0 = Normal operation. 1 = Activity LED only responds to receive operation.
RW
0
21
11
7_Wire_Enable
RW
0
21
10
CONF_ALED
0 = Activity LED responds to receive and transmit operations for Half Duplex. LED responds to receive activity in Full Duplex operation. This bit should be ignored when Register 0.8 is set to 1 or during repeater mode operation.
RW
0
21
9
LED_SEL
1 = Select NetPHY-1LP device `s Standard LED configuration. 0 = Use the Advanced LED configuration. 0 = Enable far-end-fault generation and detection function.
RW
Set by LEDRX/ LED_SEL Set by TECH[2:0], FX_SEL, ANEGA pins
21
8
FEF_DISABLE
1 = Disable far-end-fault. This bit should be ignored when FX mode is disabled.
RW
21 21 21
7 6 5
Force FEF Transmit
This bit is set to force to transmit Far End Fault (FEF) pattern.
RW RO/ RC RW
0 0 0
RX_ER_CNT Full When Receive Error Counter is full, this bit will be set to 1. Disable RX_ER_CNT DIS_WDT 1 = Disable Receive Error Counter. 0 = Enable Receive Error Counter. 1 = Disable the watchdog timer in the decipher. 0 = Enable watchdog timer. 1 = Enable remote loopback (MDI loopback for 100BASE-TX). 0 = Disable remote loopback. 1 = Enable data scrambling.
21
4
RW
0
21
3
EN_RPBK
RW
0
Set by SCRAM_EN pin
21
2
EN_SCRM
0 = Disable data scrambling. When FX mode is selected, this bit will be forced to 0.
RW
21
1
PCSBP
1 = Bypass PCS. 0 = Enable PC. 1 = FX mode selected. 0 = Disable FX mode.
RW
Set by PCSBP pin
Set by FX_SEL pin
21
0
FX_SEL
RW
AM79C874
39
PRELIMINARY Disconnect Counter Register (Register 23) Table 24. Disconnect Counter (Register 23)
Reg 23 Bit 15:0 Name DLOCK drop counter Description Count of PLL lock drop events Read/ Write RW Default 0000
Receive Error Counter Register (Register 24) Table 25.
Reg 24 Bit 15:0 Name RX_ER counter
Receive Error Counter Register (Register 24)
Read/ Write RW Default 0000
Description Count of receive error events
40
AM79C874
PRELIMINARY
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . .-55C to +150C Ambient Temperature Under Bias . . .-55C to +150C Supply Voltage . . . . . . . . . . . . . . . . . . -0.5 V to +5.5 V Voltage Applied to any input pin. . . . . . . -0.5 V to VDD Stresses above those listed under Absolute Maximum Ratings may cause permanent device failure. Functionality at or above these limits is not implied. Exposure to absolute maximum ratings for extended periods may affect device reliability.
OPERATING RANGES
Commercial (C): Operating Temperature (TA) . . . . . . . . . 0C to +70C Supply Voltage (All VDD) . . . . . . . . . . . . . . +3.3 V 5% Supply Voltage (5-V tolerant pins). . . . . . . +5.0 V 5% Industrial (I): Operating Temperature (TA) . . . . . . . . -40C to +85C Supply Voltage (All VDD) . . . . . . . . . . . . . . +3.3 V 5% Supply Voltage (5-V tolerant pins). . . . . . . +5.0 V 5% Operating ranges define those limits between which functionality of the device is guaranteed.
DC CHARACTERISTICS
Note: Parametric values are the same for Commercial and Industrial devices.
Symbol VIL VIH VOL VOH VOLL VOHL VCMP VIDIFFP VOHP VOLP VSDA VSDD IIL IIH VTXOUT VTXOS VTXR
Parameter Description Input LOW Voltage Input HIGH Voltage Output LOW Voltage Output HIGH Voltage Output LOW Voltage (LED) Output HIGH Voltage (LED) Input Common-Mode Voltage PECL (Note 1) Differential Input Voltage PECL (Note 1) Output HIGH Voltage PECL (Note 4) Output LOW Voltage PECL (Note 4) Signal Detect Assertion Threshold P/P (Note 2) Signal Detect Deassertion Threshold P/P (Note 3) Input LOW Current (Note 12)
Test Conditions
Minimum
Maximum 0.8
Units V V
2.0 IOL = 8 mA IOH = -4 mA IOL (LED) = 10 mA IOL (LED) = -10 mA VDD -0.4 VDD - 1.5 VDD = Maximum PECL Load PECL Load MLT-3/10BASE-T Test Load MLT-3/10BASE-T Test Load VDD = Maximum VIN = 0.0 V VDD = Maximum VIN = 2.7 V MLT-3/10BASE-T Test Load MLT-3/10BASE-T Test Load MLT-3/10BASE-T Test Load 950 0.98 400 VDD - 1.025 VDD - 1.81 200 VDD - 0.7 1,100 VDD - 0.60 VDD - 1.62 1000 -40 2.4 0.4 0.4
V V V V V mV V V mV mV mA mA mV V -
Input HIGH Current (Note 12) Differential Output Voltage (Note 5) Differential Output Overshoot (Note 5) Differential Output Voltage Ratio (Note5 & Note 6)
40 1050 0.05 * VTXOUT 1.02
AM79C874
41
PRELIMINARY
DC CHARACTERISTICS (CONTINUED)
Symbol VTSQ VTHS VRXDTH Parameter Description RX 10BASE-T Squelch Threshold Test Conditions Sinusoid 5 MHzRX Post-Squelch Differential Sinusoid 5 MHzVTX10NE
MLT-3/10BASE-T Test Load
2.2
2.8
V
IOZ CIN
Output Leakage Current (Note 10) Input Capacitance XTL (Note 13)
0.4 V < VOUT < VDD
-30
30 3
mA pF
10BASE-T, idle 10BASE-T, normal activity ICC Power Supply Current 10BASE-T, peak 100BASE-TX 100BASE-TX, no cable Power down Notes: 1. Applies to TEST1/ FXR+, TEST0/FXR-, and SDI+ inputs only. Valid only when in PECL mode. -
30 105 130 100 20 1 mA
2. Applies to RX inputs when in MLT-3 mode only. The RX input is guaranteed to assert internal signal detect for any valid peak-to-peak input signal greater than VSDA MIN. 3. Applies to RX inputs when in MLT-3 mode only. The RX input is guaranteed to de-assert internal signal for any peak to peak signal less than VSDD MAX. 4. Applies to FXT+ and FXT- outputs only. Valid only when in PECL mode. 5. Applies to TX differential outputs only. Valid only when in the MLT-3 mode. 6. VTXR is the ratio of the magnitude of TX in the positive direction to the magnitude of TX in the negative direction. 7. Only valid for TX output when in the 10BASE-T mode. 8. An IOLL value applies to LED pins. 9. Applies to all output pins on the MII port. 10. IOZ applies to all high-impedance output pins and all bi-directional pins. For COL and CRS parameters, IOZH limits are up to 40 mA, and IOZL up to -500 mA. 11. 75% activity means 25% IPG and 75% data. 100% activity means minimum IPG. 12. Applies to digital inputs and all bidirectional pins. These pins may have internal pull-up or pull-down resistors. RX limits up to 1.0 mA max for IIL and -1.0 mA for IIH. XTL limits up to 6.0 mA for IIL and -6.0 mA for IIH. External pull-up/pull-down resistors affect this value. 13. Parameter not measured.
42
AM79C874
PRELIMINARY
SWITCHING WAVEFORMS Key to Switching Waveforms
WAVEFORM
INPUTS Must be Steady May Change from H to L May Change from L to H Don't Care, Any Change Permitted Does Not Apply
OUTPUTS Will be Steady Will be Changing from H to L Will be Changing from L to H Changing, State Unknown Center Line is HighImpedance "Off" State
KS000010-PAL
VSDD
RX
VSDA
22235I-10
Figure 8.
MLT-3 Receive Input
AM79C874
43
PRELIMINARY
VDD 49.9
Isolation Transformer * 1:1 * TX+ 100 2% TX0.1 F 75 5% 0.01 F Chassis Ground
49.9
22235I-11
Figure 9. MLT-3 and 10BASE-T Test Load with 1:1 Transformer Ratio
VDD 78.1
Isolation Transformer * 1:25:1 * TX+ 100 2% TX0.1 F 75 5% 0.01 F Chassis Ground
78.1
22235I-12
Figure 10. MLT-3 and 10BASE-T Test Load with 1.25:1 Transformer Ratio
44
AM79C874
PRELIMINARY
VTXOS
+VTXOUT
VTXOUT
TX 112 ns
-VTXOUT
22235I-13
Figure 11.
Near-End 100BASE-TX Waveform
VTX10NE
TX 10BASE-T
22235I-14
0
Figure 12. 10BASE-T Waveform With 1:1 Transformer Ratio
5V
VDD
82.5 Pin 130 Pin
69
183
22235I-15
Figure 13. PECL Test Loads
AM79C874
45
PRELIMINARY
SWITCHING CHARACTERISTICS
Note: Parametric values are the same for commercial devices and industrial devices.
System Clock Signal
Symbol tCLK tCLKH tCLKL tCLR tCLF Parameter Description REFCLK Period REFCLK Width HIGH REFCLK Width LOW REFCLK Rise Time REFCLK Fall Time Min. 39.998 18 18 Max. 40.002 22 22 5 5 Unit ns ns ns ns ns
tCLK tCLKH REFCLK tCLKL tCLF tCLR 80% 20%
22235I-16
Figure 14. Clock Signal
MLT-3 Signals
Symbol tTXR tTXF tTXRFS tTXDCD tTXJ Parameter Description Rise Time of MLT-3 Signal Fall Time of MLT-3 Signal Rise Time and Fall Time Symmetry of MLT-3 Signal Duty Cycle Distortion Peak to Peak Transmit Jitter Using Scrambled Idle Signals Min. 3.0 3.0 Max. 5.0 5.0 5 0.5 1.4 Unit ns ns % ns ns
1 tTXR
0 tTXF
1
0
1
0
1
TX 16 ns
tXTDCD
tXTDCD
22235I-17
Figure 15.
MLT-3 Test Waveform
46
AM79C874
PRELIMINARY
MII Management Signals
Symbol tMDPER tMDWH tMDWL tMDPD tMDS tMDH Parameter Description MDC Period MDC Pulse Width HIGH MDC Pulse Width LOW MDIO Delay From Rising Edge of MDC MDIO Setup Time to Rising Edge of MDC MDIO Hold Time From Rising Edge of MDC 4 3 Min. 40 16 16 20 Max. Unit ns ns ns ns ns ns
tMDPER tMDWH MDC tMDPD MDIO mdio_tx.vsd tMDWL
22235I-18
Figure 16. Management Bus Transmit Timing
MDC tMDS MDIO tMDH
22235I-19
Figure 17. Management Bus Receive Timing
AM79C874
47
PRELIMINARY
MII Signals
100 Mbps MII Transmit Timing
Symbol tMTS100 tMTH100 tMTEJ100 tMTECRH100 tMTECOH100 tMTDCRL100 tMTDCOL100 tMTIDLE100 tMTP100 tMTWH100 tMTWL100
Parameter Description TX_ER,TX_EN, TXD[3:0] Setup Time to TX_CLK Rising Edge TX_ER, TX_EN, TXD[3:0] Hold time From TX_CLK Rising Edge Transmit Latency TX_EN Sampled by TX_CLK to First Bit of /J/ CRS Assert From TX_EN Sampled HIGH COL Assert From TX_EN Sampled HIGH CRS De-assert From TX_EN Sampled LOW COL De-assert From TX_EN Sampled LOW Required De-assertion Time Between Packets TX_CLK Period TX_CLK HIGH TX_CLK LOW
Min. 12 0 60 13 120 39.998 18 18
Max. 140 40 200 160 240 40.002 22 22
Unit ns ns ns ns ns ns ns ns ns ns ns
tMTP100 tMTWH100 tMTWL100
TX_CLK tMTS100
TX_EN tMTECRH100
CRS tMTECOH100
COL tMTS100 TX_ER TXD[3:0] tMTEJ100 TX /J/ tMTH100
22235I-20
Figure 18.
100 Mbps MII Transmit Start of Packet Timing
48
AM79C874
PRELIMINARY 100 Mbps MII Transmit Timing (Continued)
TX_CLK tMTIDLE100 TX_EN tMTDCRL100 CRS
tMTDCOL100 COL
TX /T/ /J/
22235I-21
Figure 19. 100 Mbps Transmit End of Packet Timing
AM79C874
49
PRELIMINARY 100 Mbps MII Receive Timing
Symbol tMRJCRH100 tMRJCOH100 tMRTCRL100 tMRTCOL100 tMRERL100 tMRJRA100 tMRRDC100 tMRCRD100
Parameter Description CRS HIGH After First Bit of /J/ COL HIGH After First Bit of /J/ First Bit of /T/ to CRS LOW First Bit of /T/ to COL LOW First Bit of /T/ to RXD[3:0], RX_DV De-Asserting (Going LOW) First Bit of/J/ to RXD[3:0], RX_DV, and RX_EN Active RXD[3:0], RX_DV, RX_ER valid prior to the Rising Edge of RX_CLK RXD[3:0], RX_DV, RX_ER valid after the Rising Edge of RX_CLK
Min. 80 130 130 120 TBD 10 10
Max. 200 150 240 240 140 TBD
Unit ns ns ns ns ns ns ns ns
RX tMRJCRH100 CRS tMRJCOH100 COL
/J/K/
tMRJRA100
RX_CLK tMRRDC100 RXD[3:0] RX_DV RX_ER tMRCRD100
22235I-22
Figure 20. 100 Mbps MII Receive Start of Packet Timing
50
AM79C874
PRELIMINARY 100 Mbps MII Receive Timing (Continued)
RX tMRTCRL100 CRS tMRTCOL100 COL
/T/R/
RX_CLK tMRERL100 RXD[3:0] RX_DV RX_ER
22235I-23
Figure 21. 100 Mbps MII Receive End of Packet Timing
AM79C874
51
PRELIMINARY 10 Mbps MII Transmit Timing
Symbol tMTS10 tMTH10 tMTEP10 tMTECRH10 tMTECOH10 tMTDCRL10 tMTDCOL10 tMTIDLE10 tMTP10 tMTWH10 tMTWL10 Parameter Description TX_EN, TXD10[3:0] Setup Time to TX_CLK Rising Edge TX_EN, TXD10[3:0] Hold time From TX_CLK Rising Edge Transmit Latency TX_EN Sampled by TX_CLK to Start of Packet CRS Assert from TX_EN Sampled HIGH COL Assert from TX_EN Sampled HIGH CRS De-assert From TX_EN Sampled LOW COL De-assert From TX_EN Sampled LOW Required De-assertion Time Between Packets TX_CLK Period TX_CLK HIGH TX_CLK LOW Min. 12 0 240 300 399.98 180 180 Max. 360 130 300 130 130 400.02 220 220 Unit ns ns ns ns ns ns ns ns ns ns ns
tMTP10 tMTWH10
TX_CLK
tMTWL10
tMTS10
TX_EN
tMTS10
TXD[3:0]
tMTH100
tMTECRH10
CRS
tMTECLH10
COL
tMTEP10
TX
22235I-24
Figure 22. 10 Mbps MII Transmit Start of Packet Timing
52
AM79C874
PRELIMINARY
TX_CLK tMTIDLE10 TX_EN tMTDCRL10 CRS tMTDCOL10 COL
TX
22235I-25
Figure 23. 10 Mbps MII Transmit End of Packet Timing
AM79C874
53
PRELIMINARY 10 Mbps MII Receive Timing
Symbol tMRPCRH10 tMRPCOH10
tMRCHR10
Parameter Description CRS HIGH After Start of Packet COL HIGH After Start of Packet RXD[3:0], RX_DV, RX_ER Valid after CRS HIGH RXD[3:0], RX_DV, RX_ER Valid Prior to the Rising of RX_CLK10 RXD[3:0], RX_DV, RX_ER Valid After the Rising Edge of RX_CLK End of Packet to CRS LOW End of Packet to COL LOW End of Packet to RXD[3:0], RX_DV, RX_ER De-Asserting (Going LOW)
Min. 80 80 100 16 12 130 125 120
Max. 150 150 100 190 185 140
Unit ns ns ns ns ns ns ns ns
tMRRC10 tMRCRD10 tMRECRL10 tMRECOL10 tMRERL10
RX tMRPCRH10 CRS tMRPCOH10 COL
RX_CLK tMRCHR10 RXD[3:0] RX_DV RX_ER t MRRC10 t MRCR10
22235I-26
Figure 24. 10 Mbps MII Receive Start of Packet Timing
54
AM79C874
PRELIMINARY 10 Mbps MII Receive Timing (Continued)
RX tMRECRL10 CRS tMRECOL10 COL
RX_CLK tMRERL10 RXD[3:0] RX_DV RX_ER
22235I-27
Figure 25. 10 Mbps MII Receive End of Packet Timing
AM79C874
55
PRELIMINARY
GPSI Signals
10 Mbps GPSI Receive Timing
Symbol tGCD tGRCD Parameter Description 10CRS HIGH To First Bit Of Data Rising Edge of 10RXCLK to 10RXD or 10CRS Min. 750 45 Max. 850 55 Unit ns ns
RX
Bit Cell 1 1
Bit Cell 2 0
Bit Cell 3 1
Bit Cell 4 0
Bit Cell 5 1
1 tGRCD 10CRS 10RXCLK
0
1
0
1
tGRCD tGCD 10RXD
22235I-28
Figure 26. GPSI Receive Timing - Start of Reception
10 Mbps GPSI Receive Timing
Symbol tGRCD Parameter Description Rising Edge of 10RXCLK to 10RXD or 10CRS Min. 45 Max. 55 Unit ns
1 Bit (N _ 1) RX
0 Bit N
10CRS tGRCD
10RXCLK tGRCD 10RXD Bit (N _ 1) Bit N
22235I-29
Figure 27. GPSI Receive Timing - End of Reception (Last Bit = 0)
56
AM79C874
PRELIMINARY 10 Mbps GPSI Receive Timing
Symbol tGDOFF tGRCD Parameter Description Delay from RX going to 1 to the Rising Edge of 10RXCLK, which clocks out the last bit of data on 10RXD Rising Edge of 10RXCLK to 10RXD or 10CRS 45 Min. Max. 190 55 Unit ns ns
0 Bit (N _ 1) RX
1 Bit N
10RXCLK tGDOFF 10RXD Bit (N _ 1) Bit N tGRCD 10CRS
22235I-30
Figure 28. GPSI Receive Timing - End of Reception (Last Bit = 1)
10 Mbps GPSI Collision Timing
Symbol tGCSCLH tGCECLL Parameter Description Collision Start to 10COL HIGH Collision End to 10COL LOW Min. 80 125 Max. 150 185 Unit ns ns
Collision Presence
0V
+
tGCSCLH 10COL
tGCECLL
22235I-31
Figure 29. GPSI Collision Timing
AM79C874
57
PRELIMINARY 10 Mbps GPSI Transmit Timing
Symbol tGTTX Parameter Description Delay from the rising edge of the 10TXCLK which first clocks 10TXEN HIGH to TX toggling LOW Min. 240 Max. 360 Unit ns
10TXCLK
10TXEN TX
tGTTX
22235I-32
Figure 30.
GPSI Transmit Timing - Start of Transmission
10 Mbps GPSI Transmit Timing
Symbol tGTCDH tGDTCS tGTCH tGTCL tGTCP Parameter Description 10TXCLK to 10TXD or 10TXEN Hold Time 10TXD or 10TXEN to 10TXCLK Setup Time 10TXCLK Width HIGH 10TXCLK Width LOW 10TXCLK Period Min. 20 20 45 45 99,995 55 55 100,005 Max. Unit ns ns ns ns ns
tGTCP tGTCH 10TXCLK tGTCDH 10TXD tGDTCS 10TXEN
22235E-36
tGTCL
tGTCDH
Figure 31. GPSI Transmit 10TXCLK and 10TXD Timing
DUT 50 pF
22235E-37
Figure 32. Test Load for 10RXD, 10CRS, 10RXCLK, 10TXCLK and 10COL
58
AM79C874
PRELIMINARY
PHYSICAL DIMENSIONS PQT80 (measured in millimeters)
80-Lead Thin Plastic Quad Flat Pack (PQT)
Dwg rev. AE; 8/99
PQT80
AM79C874
59
PRELIMINARY
REVISION SUMMARY
Revisions to other versions this document are as follows: Revision C to D 1. Corrected reversal of Figure 4 and Figure 5 in LED section. 2. Changed ECL to PECL. Revision D to E 1. Added GPSI timing and diagrams 2. Added Industrial Temperature support Revision E to F 1. Minor edits Revision F to G 1. Minor edits Revision G to H 1. PHYAD pins: Specified using resistors in the range of 1 kW to 4.7 kW for setting PHYAD pins. In GPSI mode, PHYAD pins must be set to addresses other than 00h. 2. DC Characteristics added: VOLL and VOHL 3. DC Characteristics, added new values for: IIL, IIH, IOZ. Figure 6, Advanced LED Configuration, changes to Receive LED component changes. Revision H to I 1. Added clarification to RX_CLK throughout document, which is active only while LINK is established. See pin description for more information. 2. Added Flow Control descriptions to registers 4 and 5 3. Register 21, bit 9 was reversed: 1 selects the standard LED configuration, while 0 selects the advanced LED configuration 4. Register 21, bit 2 was changed to indicate EN_SCRM, Scrambler Enable; a 1 enables the scrambler. This register is set by the SCRAM_EN pin 5. Maximum input voltage is 5.5 V; operating voltage for 5-V tolerant pins is 5.0 V 6. Minor edits
The contents of this document are provided in connection with Advanced Micro Devices, Inc. ("AMD") products. AMD makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in AMD's Standard Terms and Conditions of Sale, AMD assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. AMD's products are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of AMD's product could create a situation where personal injury, death, or severe property or environmental damage may occur. AMD reserves the right to discontinue or make changes to its products at any time without notice. Trademarks Copyright (c) 1999, 2000, 2001 Advanced Micro Devices, Inc. All rights reserved. AMD, the AMD logo and combinations thereof, PCnet-PRO and NetPHY are trademarks of Advanced Micro Devices, Inc. Other product names used in this publication are for identification purposes only and may be trademarks of their respective companies.
60
AM79C874

▲Up To Search▲

Price & Availability of AM79C874

	To Download AM79C874 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .